Design of thermal-insulated pipes applied in deepwater well to mitigate annular pressure build-up

Abstract Annular pressure build-up threatens deepwater well safety greatly, but the available mitigation methods are limited by well conditions and formation properties in some cases. Thermal-insulated pipes including casing and tubing are an alternative method due to low thermal conductivity. To optimize the application of thermal-insulted pipes, a model based on volume consistency and semi-steady approach is established to calculate the annular pressure in multiple annuli with thermal-insulated pipes. In the case well, the optimal setting depth is 2200 m, equal to cement top. Annular pressure decreases quickly when thermal conductivity is under 0.04 W/(m⋅k). Thermal-insulated pipes can reduce the rising speed of annular pressure as formation temperature increases. The effect of production rate can be ignored if it is higher than 400 t/d. The annular pressure of case well is reduced by as much as 63.97% and kept under maxim acceptable annular pressure in 10 years. Based on this model and analysis, a process is proposed to design the thermal pipes applied in deepwater well to mitigate annular pressure build-up.

[1]  P. Daling,et al.  Chemical comparison and acute toxicity of water accommodated fraction (WAF) of source and field collected Macondo oils from the Deepwater Horizon spill. , 2015, Marine pollution bulletin.

[2]  Mike Payne,et al.  Practical and Successful Prevention of Annular Pressure Buildup on the Marlin Project , 2003 .

[3]  D. L. Flock,et al.  Wellbore Behaviour During Saturated Steam Injection , 1966 .

[4]  N. Chen.  An Explicit Equation for Friction Factor in Pipe , 1979 .

[5]  Ryan G. Ezell,et al.  High Performance Aqueous Insulating Packer Fluid Improved Flow Assurance and Reduced Annular Pressure Buildup in Ultra Deepwater Wells , 2010 .

[6]  H. J. Ramey.  Wellbore Heat Transmission , 1962 .

[7]  Siva Rama Krishna Jandhyala,et al.  Finite Element Approach to Predict the Effect of Annular Pressure Buildup on Wellbore Materials , 2014 .

[8]  P. D. Pattillo,et al.  Application of Vacuum Insulated Tubing to Mitigate Annular Pressure Buildup , 2007 .

[9]  Chris Carpenter,et al.  Newtonian Fluids in Cementing Operations in Deepwater Wells , 2014 .

[10]  Bulent Izgec,et al.  Sustaining Production by Managing Annular-Pressure Buildup , 2010 .

[11]  C. S. Kabir,et al.  Heat Transfer During Two-Phase Flow in Wellbores; Part I--Formation Temperature , 1991 .

[12]  Cnooc Lt,et al.  Research on calculation of casing annulus trapped pressure and its control techniques for deep water well , 2014 .

[13]  Weidong Zhou,et al.  Design and Performance Evaluation of A Unique Deepwater Cement Slurry , 2011 .

[14]  Marcus V.D. Ferreira,et al.  Thermally Insulated Tubing Application to Prevent Annular Pressure Buildup in Brazil Offshore Fields , 2012 .

[15]  W. W. Sanders,et al.  Control of Contained-Annulus Fluid Pressure Buildup , 2003 .

[16]  E. Kårstad.  Analysis of Ballooning Effects During Drilling of High Pressure High Temperature Wells , 1998 .

[17]  Mike Payne,et al.  Development of a Screening System to Identify Deepwater Wells at Risk for Annular Pressure Build-up , 2005 .

[18]  K. Chiu,et al.  Modeling of Wellbore Heat Losses in Directional Wells Under Changing Injection Conditions. , 1991 .

[19]  I. L. Purdy,et al.  Evaluation of Vacuum-Insulated Tubing for Paraffin Control at Norman Wells , 1991 .

[20]  Farzad Tahmourpour,et al.  Different Methods To Avoid Annular Pressure Buildup by Appropriate Engineered Sealant and Applying Best Practices (Cementing and Drilling) , 2010 .

[21]  S. W. Gosch,et al.  Marlin Failure Analysis and Redesign: Part 3 - VIT Completion With Real-Time Monitoring , 2004 .

[22]  Jin Yang,et al.  Prediction model of casing annulus pressure for deepwater well drilling and completion operation , 2013 .

[23]  P. D. Pattillo,et al.  Analysis of an Annular Pressure Buildup Failure During Drill Ahead , 2006 .

[24]  D. H. Gibson,et al.  Marlin Failure Analysis and Redesign; Part 1, Description of Failure , 2002 .

[25]  P. D. Pattillo,et al.  The Heat Transfer Characteristics of Vacuum Insulated Tubing , 2004 .