Understanding the residual stress distribution in brazed polycrystalline CBN abrasive grains

[1]  Dongzhou Jia,et al.  Experimental Evaluation of the Lubrication Performance of MoS2/CNT Nanofluid for Minimal Quantity Lubrication in Ni-based Alloy Grinding , 2015 .

[2]  X. Zhang,et al.  A theoretical and experimental study on laser-induced deterioration in wet grinding of Al2O3 engineering ceramic , 2015, The International Journal of Advanced Manufacturing Technology.

[3]  Huanhuan Sun,et al.  Finite Element Analysis of Thermal Effects on Brazed Cold Diamond Grit , 2015, Transactions of the Indian Institute of Metals.

[4]  Xuekun Li,et al.  Modelling and analysis of the bonding mechanism of CBN grains for electroplated superabrasive tools—part 1: introduction and application of a novel approach for determining the bonding force and the failure modes , 2015 .

[5]  Dongzhou Jia,et al.  Experimental research on the energy ratio coefficient and specific grinding energy in nanoparticle jet MQL grinding , 2015 .

[6]  B. Shen,et al.  Optimization on the HFCVD setup for the mass-production of diamond-coated micro-tools based on the FVM temperature simulation , 2014 .

[7]  M. I. Barrena,et al.  Numerical simulation and experimental analysis of vacuum brazing for steel/cermet , 2014 .

[8]  Zhixiong Zhou,et al.  Analysis of suspension stability for nanofluid applied in minimum quantity lubricant grinding , 2014 .

[9]  Durul Ulutan,et al.  Determination of tool friction in presence of flank wear and stress distribution based validation using finite element simulations in machining of titanium and nickel based alloys , 2013 .

[10]  Tuğrul Özel,et al.  Experimental and finite element simulation based investigations on micro-milling Ti-6Al-4V titanium alloy: Effects of cBN coating on tool wear , 2013 .

[11]  Zhixiong Zhou,et al.  Investigation on the Effect of Nanofluid Parameters on MQL Grinding , 2013 .

[12]  C. Leinenbach,et al.  Thermomechanical analysis of residual stresses in brazed diamond metal joints using Raman spectroscopy and finite element simulation , 2012 .

[13]  K. Kurzydłowski,et al.  FEM modelling of the combined effect of grain boundaries and second phase particles on the flow stress of nanocrystalline metals , 2012 .

[14]  A. K. Chattopadhyay,et al.  On the grindability of low-carbon steel under dry, cryogenic and neat oil environments with monolayer brazed cBN and alumina wheels , 2011 .

[15]  Jiu-hua Xu,et al.  Grain wear of brazed polycrystalline CBN abrasive tools during constant-force grinding Ti–6Al–4V alloy , 2011 .

[16]  Aldo Attanasio,et al.  Investigation and FEM-based simulation of tool wear in turning operations with uncoated carbide tools , 2010 .

[17]  X. Ling,et al.  Numerical Analysis of Residual Stress for Copper Base Brazed Stainless Steel Plate-Fin Structure , 2010 .

[18]  A. B. Chattopadhyay,et al.  Development and performance evaluation of monolayer brazed cBN grinding wheel on bearing steel , 2010 .

[19]  R. Kang,et al.  Subsurface crystal lattice deformation machined by ultraprecision grinding of soft-brittle CdZnTe crystals , 2010 .

[20]  C. Leinenbach,et al.  Influence of the brazing parameters on microstructure, residual stresses and shear strength of diamond–metal joints , 2010 .

[21]  Ji-cai Feng,et al.  Effect of Reaction Layers on the Residual Stress of the Brazed TiC Cermets/Steel Joints , 2009 .

[22]  T. Tawakoli,et al.  Effect of the Coolant Lubricant Type and Dress Parameters on CBN Grinding Wheels Performance , 2009 .

[23]  J. Janczak-Rusch,et al.  Characterization of the Residual Stresses and Strength of Ceramic-Metal Braze Joints , 2009 .

[24]  M. Suh,et al.  Wear behavior of diamond wheel for grinding optical connector ferrule — FEA and wear test — , 2008 .

[25]  Jiu-hua Xu,et al.  Joining of CBN abrasive grains to medium carbon steel with AgCu/Ti powder mixture as active brazing alloy , 2006 .

[26]  I. A. Petrusha,et al.  Mechanical properties of polycrystalline cBN obtained from pyrolytic gBN by direct transformation technique , 2006 .

[27]  J. Schmidt,et al.  2D FEM estimate of tool wear in turning operation , 2005 .

[28]  Xipeng Xu,et al.  Effect of grinding temperatures on the surface integrity of a nickel-based superalloy , 2002 .

[29]  Wilhelm Kulisch,et al.  Stress of c-BN thin films: a parameter investigation , 1999 .

[30]  Jiu-hua Xu,et al.  The effects of solder alloys on the morphologies and mechanical properties of brazed diamond grits , 2014 .

[31]  Jiu-hua Xu,et al.  Interface characteristics and fracture behavior of brazed polycrystalline CBN grains using Cu–Sn–Ti alloy , 2013 .

[32]  Jun Zhao,et al.  Cutting performance and wear mechanisms of Sialon–Si3N4 graded nano-composite ceramic cutting tools , 2012 .

[33]  M. Fujimoto,et al.  Development of a High Performance Vitrified Grinding Wheel using Ultrafine-Crystalline cBN Abrasive Grains , 2010 .

[34]  Xing Xian-ran.  THERMAL EXPANSION OF CUBIC BORON NITRIDE , 2003 .

[35]  Tuğrul Özel,et al.  Journal of Materials Processing Technology Computational Modelling of 3d Turning: Influence of Edge Micro-geometry on Forces, Stresses, Friction and Tool Wear in Pcbn Tooling , 2022 .