Numerical and experimental investigation of the joint stiffness in lattice structures fabricated by additive manufacturing

Abstract In this paper, a concept called joint stiffening element is proposed to represent the influence of the joint on the stiffness of lattice structures fabricated by additive manufacturing. Four parameters are defined in the proposed element to quantify the increment of the stiffness caused by the lattice joint. Then, three-point-bend testing is used to validate the proposed model. The lattice structures with Cubic-center and Vintiles topologies are designed and fabricated for the experiment. As-fabricated material properties are obtained by tensile specimens to eliminate the influence caused by the manufacturing process and to isolate the joint stiffening effect. The result shows that models with the solid element and the proposed element are both accurate, but the proposed model has a significantly less computational cost than the solid element model. Furthermore, compared to the beam element model, the proposed model can more accurately estimate the stiffness of lattice structures, especially for the Vintiles topology. It is also found that the joint stiffening effect is more significant on the bending dominant topology than the stretching dominant topology.

[1]  David W. Rosen,et al.  Effective mechanical properties of lattice material fabricated by material extrusion additive manufacturing , 2014 .

[2]  M. Ashby,et al.  The mechanics of two-dimensional cellular materials , 1982, Proceedings of the Royal Society of London. A. Mathematical and Physical Sciences.

[3]  Mohsen Badrossamay,et al.  Numerical investigation on mechanical properties of cellular lattice structures fabricated by fused deposition modeling , 2014 .

[4]  David W. Rosen,et al.  Homogenization of Mechanical Properties for Additively Manufactured Periodic Lattice Structures Considering Joint Stiffening Effects , 2016 .

[5]  D. Inman,et al.  Dynamic analysis of a lattice structure by homogenization: Experimental validation , 2008 .

[6]  G. J. McShane,et al.  Plate-impact loading of cellular structures formed by selective laser melting , 2012 .

[7]  T. Tancogne-Dejean,et al.  Additively-manufactured metallic micro-lattice materials for high specific energy absorption under static and dynamic loading , 2016 .

[8]  David Rosen,et al.  Design of truss-like cellular structures using relative density mapping method , 2015 .

[9]  Ziyu Zhang,et al.  Failure modes in high strength and stiffness to weight scaffolds produced by Selective Laser Melting , 2015 .

[10]  Zu-Qing Qu,et al.  Model Order Reduction Techniques with Applications in Finite Element Analysis , 2004 .

[11]  Radovan Kovacevic,et al.  Fatigue properties of a dental implant produced by electron beam melting® (EBM) , 2015 .

[12]  M. Ashby,et al.  The mechanics of three-dimensional cellular materials , 1982, Proceedings of the Royal Society of London. A. Mathematical and Physical Sciences.

[13]  Osvaldo M. Querin,et al.  Optimum design of semi-rigid connections using metamodels , 2012 .

[14]  K. Bathe.  Finite Element Procedures , 1995 .

[15]  J. Reddy.  An introduction to the finite element method , 1989 .

[16]  Li Yang,et al.  Non-stochastic Ti–6Al–4V foam structures with negative Poisson's ratio , 2012 .

[17]  Li Yang,et al.  Mechanical properties of 3D re-entrant honeycomb auxetic structures realized via additive manufacturing , 2015 .

[18]  M. Smith,et al.  Finite element modelling of the compressive response of lattice structures manufactured using the selective laser melting technique , 2013 .

[19]  Yaoyao Fiona Zhao,et al.  Lattice Structure Design and Optimization With Additive Manufacturing Constraints , 2018, IEEE Transactions on Automation Science and Engineering.

[20]  M. H. Luxner,et al.  Finite element modeling concepts and linear analyses of 3D regular open cell structures , 2005 .

[21]  S. Lohfeld,et al.  Finite element predictions compared to experimental results for the effective modulus of bone tissue engineering scaffolds fabricated by selective laser sintering , 2009, Journal of materials science. Materials in medicine.

[22]  Hadley Brooks,et al.  Design of conformal cooling layers with self-supporting lattices for additively manufactured tooling , 2016 .

[23]  A. A. Zadpoor,et al.  Mechanical properties of open-cell metallic biomaterials manufactured using additive manufacturing , 2013 .

[24]  R. Dendievel,et al.  Towards stiffness prediction of cellular structures made by electron beam melting (EBM) , 2014 .

[25]  Yaoyao Fiona Zhao,et al.  A Survey of Modeling of Lattice Structures Fabricated by Additive Manufacturing , 2017 .

[26]  G. N. Labeas,et al.  Investigation on the Static Response and Failure Process of Metallic Open Lattice Cellular Structures , 2010 .

[27]  Liang Hao,et al.  Fracture toughness and tensile strength of 316L stainless steel cellular lattice structures manufactured using the selective laser melting technique , 2016 .