Effects of cylindrical cruciform patterns on fluid flow and drag as determined by CFD models

Fluid flow around and drag of two cylindrical cruciform patterns, conventional (T0) and rotated 45o in its own plane (T45), were numerically investigated by solving three-dimensional Reynolds-averaged Navier-Stokes equations within the subcritical flow regime over angles of attack (AOA) from 90o to 0o. Firstly, the drag for a one-cruciform element was assessed, followed by analysis of a four-cruciform assembly (‘square mesh’) to take into account the wake effect of tandem elements. For the one-cruciform element, T45 experienced a less prominent streamline separation and consequently lower drag between 90° and 45° AOA, while T0 experienced progressively lower drag below 45° AOA owing to re-establishment of smoother streamlines caused by the gradually reduced circulation momentum from the adjacent vortex that rotates in the off-side direction. For the four-cruciform assemblies, T0 and T45 drag was essentially equal above 45o AOA; while below 45o, T45 had greater drag attributed to more prominent spanwise vortex downstream development. Overall, while the largest relative difference between the two orientations was 26.2% and 33.8% for the one- and four-cruciform configurations respectively at 0° AOA, for 30o and above AOA there were limited drag differences (generally below 10%).

[1]  Martin Føre,et al.  Numerical Modeling of Wake Effect on Aquaculture Nets , 2013 .

[2]  Yang Liu,et al.  Investigation of turbulent flow past a yawed wavy cylinder , 2010 .

[3]  Jie-Min Zhan,et al.  Analytical and experimental investigation of drag on nets of fish cages , 2006 .

[4]  S. Hoerner.  Fluid Dynamic Drag: Practical Information on Aerodynamic Drag and Hydrodynamic Resistance , 1965 .

[5]  Bjørnar Pettersen,et al.  Forces on a cruciform/sphere structure in uniform current , 2014 .

[6]  Mark S. Shephard,et al.  Boundary layer mesh generation for viscous flow simulations , 2000 .

[7]  P. Bradshaw,et al.  Turbulence Models and Their Application in Hydraulics. By W. RODI. International Association for Hydraulic Research, Delft, 1980. Paperback US $15. , 1983, Journal of Fluid Mechanics.

[8]  Tim Craft,et al.  Progress in the generalization of wall-function treatments , 2002 .

[9]  Neil Bose,et al.  The effect of mesh orientation on netting drag and its application to innovative prawn trawl design , 2015 .

[10]  H. Osaka,et al.  The Structure of a Turbulent Wake behind a Cruciform Circular Cylinder : 1st Report, The Mean Velocity Field , 1983 .

[11]  Andrew Drach,et al.  Characterization of geometry and normal drag coefficients of copper nets , 2011 .

[12]  Knut O. Ronold,et al.  New DNV Recommended Practice DNV-RP-C205 On Environmental Conditions And Environmental Loads , 2006 .

[13]  N. Bose,et al.  Aquaculture Net Drag Force and Added Mass , 2009 .

[14]  Arne Fredheim.  Current Forces on Net Structure , 2005 .

[15]  Odd M. Faltinsen,et al.  Modelling of current loads on aquaculture net cages , 2012 .

[16]  H. Osaka,et al.  The Structure of a Turbulent Wake Behind a Cruciform Circular Cylinder : 2nd Report, The Streamwise Development of turbulent flow field , 1983 .

[17]  Kurt Hansen,et al.  Current Loads on Net Panels With Rhombic Meshes , 2012 .

[18]  Ming Zhao,et al.  Direct numerical simulation of three-dimensional flow past a yawed circular cylinder of infinite length , 2009 .

[19]  F. Menter.  Two-equation eddy-viscosity turbulence models for engineering applications , 1994 .

[20]  Pål Lader,et al.  Hydrodynamic interactions on net panel and aquaculture fish cages: A review , 2013 .