A study of 3-D numerical simulation and comparison with experimental results on turbulent flow of venting flue gas using thermoelectric generator modules and plate fin heat sink

This paper investigates the three-dimensional turbulent flow in a chimney used for venting flue gas from either a boiler or stove. The thermoelectric generator (TEG) modules are embedded in the chimney walls. To understand the power output performance of the TEG module, three-dimensional numerical simulations combining convection and radiation effects, including the chimney tunnel, TEG modules, plate-fin heat sinks and cold plates, based on water cooling are developed and solved simultaneously. The effects of operational parameters such as the flue gas velocity (Vin = 3, 5 and 10 m/s) and flue gas temperatures (Tgas = 500, 600 and 700 K) on the flow and heat transfer are determined. The influences of the plate-fin height (Hfin) and number of fins (N), ranging from 0 mm < Hfin < 100 mm and 4 < N < 8 respectively, on the power output and pressure drop are also described in detail. It is worthy of note that the net electric power (Pnet) of the TEG module was obtained using the ideal electric power (PTEG) minus the extra pumping power (Pfan). The numerical results for the power vs. current (P–I) curve are in good agreement with the experimental data within an error of 9%.

[1]  J. Truelove,et al.  Discrete-Ordinate Solutions of the Radiation Transport Equation , 1987 .

[2]  S. W. Angrist.  Direct energy conversion , 1976 .

[3]  Katsutoshi Ono,et al.  Thermoelectric power generation: Converting low-grade heat into electricity , 1998 .

[4]  David Michael Rowe,et al.  Applications of nuclear-powered thermoelectric generators in space , 1991 .

[5]  Robert J. Moffat,et al.  Describing the Uncertainties in Experimental Results , 1988 .

[6]  Jianlin Yu,et al.  Experimental study on low-temperature waste heat thermoelectric generator , 2009 .

[7]  David Michael Rowe,et al.  Thermoelectrics, an environmentally-friendly source of electrical power , 1999 .

[8]  A. Bejan.  Advanced Engineering Thermodynamics , 1988 .

[9]  Seri Lee.  Optimum design and selection of heat sinks , 1995 .

[10]  Jing Liu,et al.  Liquid metal based thermoelectric generation system for waste heat recovery , 2011 .

[11]  Brian T. Helenbrook,et al.  Testing of an automobile exhaust thermoelectric generator in a light truck , 2007 .

[12]  Chin-Hsiang Cheng,et al.  A three-dimensional theoretical model for predicting transient thermal behavior of thermoelectric coolers , 2010 .

[13]  M. Modest.  Radiative heat transfer , 1993 .

[14]  M. Rivaletto,et al.  Study of a TE (thermoelectric) generator incorporated in a multifunction wood stove , 2011 .

[15]  M. Pinar Mengüç,et al.  Thermal Radiation Heat Transfer , 2020 .

[16]  D. Astrain,et al.  Study of the influence of heat exchangers' thermal resistances on a thermoelectric generation system , 2010 .

[17]  Frank P. Incropera,et al.  Fundamentals of Heat and Mass Transfer , 1981 .

[18]  Emil Sandoz-Rosado,et al.  Robust Finite Element Model for the Design of Thermoelectric Modules , 2010 .

[19]  Bahram Moshfegh,et al.  Modeling of the thermal and hydraulic performance of plate fin, strip fin, and pin fin heat sinks-influence of flow bypass , 2001 .

[20]  J. P. V. Doormaal,et al.  ENHANCEMENTS OF THE SIMPLE METHOD FOR PREDICTING INCOMPRESSIBLE FLUID FLOWS , 1984 .

[21]  Gao Min,et al.  Evaluation of thermoelectric modules for power generation , 1998 .

[22]  G. Jackson,et al.  Optimization of cross flow heat exchangers for thermoelectric waste heat recovery , 2004 .

[23]  Prasanta Kumar Das,et al.  Constructal design of a thermoelectric device , 2006 .

[24]  W. Fiveland.  Discrete-Ordinates Solutions of the Radiative Transport Equation for Rectangular Enclosures , 1984 .

[25]  A. V. Barrett,et al.  Characterization of longitudinal fin heat sink thermal performance and flow bypass effects through CFD methods , 1997, Thirteenth Annual IEEE. Semiconductor Thermal Measurement and Management Symposium.

[26]  Zijun Yan,et al.  The influence of Thomson effect on the maximum power output and maximum efficiency of a thermoelectric generator , 1996 .

[27]  Antonios Liakopoulos,et al.  Explicit Representations of the Complete Velocity Profile in a Turbulent Boundary Layer , 1984 .

[28]  Ten-See Wang,et al.  Unified Navier-Stokes flowfield and performance analysis of liquid rocket engines , 1993 .

[29]  P. E. Liley,et al.  Steam and Gas Tables with Computer Equations , 1984 .

[30]  Wei-Chin Chang,et al.  A mathematic model of thermoelectric module with applications on waste heat recovery from automobile engine , 2010 .

[31]  Kim Choon Ng,et al.  A general model for studying effects of interface layers on thermoelectric devices performance , 2002 .

[32]  David Michael Rowe,et al.  A high performance solar powered thermoelectric generator , 1981 .

[33]  Gao Min,et al.  Optimisation of thermoelectric module geometry for ‘waste heat’ electric power generation , 1992 .

[34]  L. Rosendahl,et al.  A three-dimensional numerical model of thermoelectric generators in fluid power systems , 2011 .

[35]  Gang Chen,et al.  Bulk nanostructured thermoelectric materials: current research and future prospects , 2009 .

[36]  Christophe Goupil,et al.  Comparison of different modeling approaches for thermoelectric elements , 2013 .

[37]  Saffa Riffat,et al.  Thermoelectrics: a review of present and potential applications , 2003 .

[38]  Jiin-Yuh Jang,et al.  Optimization of thermoelectric generator module spacing and spreader thickness used in a waste heat recovery system , 2013 .