Improving thermal performance of building walls by optimizing insulation layer distribution and thickness for same thermal mass

Dynamic thermal characteristics of insulated building walls with same thermal mass are studied numerically with optimized insulation thickness under steady periodic conditions using the climatic data of Riyadh. Insulation is effected through use of one, two and three layers of insulation, the locations of which are varied in order to achieve the best performance. Insulation layer(s) thicknesses are optimized by minimizing the total cost of insulation and energy consumption using the present worth method. The results show that the optimum thickness of a single insulation layer is independent of its location in the wall; and that, when more than one insulation layer is used, their total optimum thickness is the same as the optimum thickness of a single layer. As a consequence, walls thermal resistances (R-values) are equal under optimum conditions; however, peak load, time lag, and decrement factor are found to be substantially different. The best overall performance is achieved by a wall with three layers of insulation, each 26-mm-thick, placed at inside, middle and outside followed closely by a wall with two insulation layers, each 39-mm-thick, placed at middle and outside. Comparing performance of the best wall with that of a wall with one layer of insulation, 78-mm-thick, placed on the inside, the following improvements are achieved: 100% increase in time lag from 6h to 12h; 10-fold decrease in decrement factor; 20% decrease in both peak cooling and heating transmission loads, and 1.6% and 3.2% decrease in yearly cooling and heating transmission loads, respectively. It is emphasized that all walls have the same optimized R-value and same thermal mass and therefore all improvements achieved are solely due to the developed distribution of insulation layers.

[1]  P. T. Tsilingiris.  The influence of heat capacity and its spatial distribution on the transient wall thermal behavior under the effect of harmonically time-varying driving forces , 2006 .

[2]  G. M. Zaki,et al.  Cooling load response for building walls comprising heat storing and thermal insulating layers , 1991 .

[3]  M. F. Zedan,et al.  Effect of electricity tariff on the optimum insulation-thickness in building walls as determined by a dynamic heat-transfer model , 2005 .

[4]  W. Rohsenow,et al.  Handbook of heat transfer applications , 1985 .

[5]  Ali Bolatturk,et al.  Determination of optimum insulation thickness for building walls with respect to various fuels and climate zones in Turkey , 2006 .

[6]  S. A. Al-Sanea,et al.  Heat Transfer Characteristics and Optimum Insulation Thickness for Cavity Walls , 2003 .

[7]  S. A. Al-Sanea,et al.  Evaluation of Heat Transfer Characteristics of Building Wall Elements , 2000 .

[8]  O. Kaynakli,et al.  A study on residential heating energy requirement and optimum insulation thickness , 2008 .

[9]  S. A. Al-Sanea,et al.  Adjustment factors for the ASHRAE clear-sky model based on solar-radiation measurements in Riyadh , 2004 .

[10]  Jan Kosny,et al.  Influence of insulation configuration on heating and cooling loads in a continuously used building , 2002 .

[11]  Figen Balo,et al.  Effect of fuel type on the optimum thickness of selected insulation materials for the four different climatic regions of Turkey , 2009 .

[12]  S. A. Al-Sanea,et al.  Effect of insulation location on thermal performance of building walls under steady periodic conditions , 2001 .

[13]  H. Asan.  Numerical computation of time lags and decrement factors for different building materials , 2006 .

[14]  Meral Özel,et al.  Optimum location and distribution of insulation layers on building walls with various orientations , 2007 .

[15]  S. A. Al-Sanea,et al.  Optimized monthly-fixed thermostat-setting scheme for maximum energy-savings and thermal comfort in air-conditioned spaces , 2008 .

[16]  N. K. Bansal,et al.  Optimum distribution of insulation and concrete in a multilayered wall of roof , 1981 .

[17]  Ali Bolatturk,et al.  Optimum insulation thicknesses for building walls with respect to cooling and heating degree-hours in the warmest zone of Turkey , 2008 .

[18]  M. S. Sodha,et al.  Thermal load levelling in a multilayered wall/roof , 1981 .

[19]  Meral Özel,et al.  Investigation of the most suitable location of insulation applying on building roof from maximum load levelling point of view , 2007 .

[20]  Don E Croy,et al.  Handbook of thermal insulation applications , 1984 .

[21]  H. Asan,et al.  Investigation of wall's optimum insulation position from maximum time lag and minimum decrement factor point of view , 2000 .

[22]  Naouel Daouas,et al.  A study on optimum insulation thickness in walls and energy savings in Tunisian buildings based on analytical calculation of cooling and heating transmission loads , 2011 .

[23]  Dennis L. Loveday,et al.  The influence on building thermal behavior of the insulation/masonry distribution in a three-layered construction , 1997 .

[24]  S. A. Al-Sanea,et al.  Optimum insulation thickness for building walls in a hot-dry climate , 2002 .

[25]  Liwei Tian,et al.  A study on optimum insulation thicknesses of external walls in hot summer and cold winter zone of China , 2009 .

[26]  G. Zaki,et al.  Thermal performance of composite building components with periodic solar insolation and ambient temperature , 1986 .

[27]  M.A.Eben Saleh.  Impact of thermal insulation location on buildings in hot dry climates , 1990 .

[28]  Dimitrios Bikas,et al.  The effect of south wall's outdoor absorption coefficient on time lag, decrement factor and temperature variations , 2007 .