Modeling and experimental study of an indirect evaporative cooler

Abstract The use of indirect evaporative cooling technologies is an effective way to reach high energy efficiency systems and to reduce primary energy consumption. At present, interest in such systems is strongly increasing, with particular attention to data centers facilities. In fact, in these applications the indoor air temperature can be higher than the one of residential and commercial buildings, leading to a greater number of yearly operating hours of the system. In this paper an indirect evaporative cooler, based on a cross flow heat exchanger, has been tested and modelled. Many experiments have been carried out in typical data centers operating conditions, varying both water flow rate and inlet air conditions. A phenomenological model of the indirect evaporative cooler has been developed: the model takes into account the effects of the adiabatic cooling of the secondary air stream in the inlet plenum and the actual wettability of the heat exchanger surface. The model has been extensively validated and it is shown that simulation results are in very good agreement with experimental data. Therefore, it can be a suitable tool to design and to predict performance of indirect evaporative cooling systems.

[1]  Prashant Kumar,et al.  Experimental investigation of heat transfer enhancement and fluid flow characteristics in a protruded surface heat exchanger tube , 2016 .

[2]  Paolo Liberati,et al.  Experimental analysis of a cross flow indirect evaporative cooling system , 2016 .

[3]  F. C. R. Martínez,et al.  Comparative study of two different evaporative systems: an indirect evaporative cooler and a semi-indirect ceramic evaporative cooler , 2004 .

[4]  Qiang Zhang,et al.  Thermal performance of dimpled surfaces in laminar flows , 2009 .

[5]  Sergey Bolotin,et al.  Comparative analysis of the cross-flow indirect evaporative air coolers , 2015 .

[6]  Gerard F. Jones,et al.  A review of data center cooling technology, operating conditions and the corresponding low-grade waste heat recovery opportunities , 2014 .

[7]  N. J. Stoitchkov,et al.  Effectiveness of crossflow plate heat exchanger for indirect evaporative cooling , 1998 .

[8]  Ala Hasan.  Indirect evaporative cooling of air to a sub-wet bulb temperature , 2010 .

[9]  Zhang Hainan,et al.  Free cooling of data centers: A review , 2014 .

[10]  Yang Hongxing,et al.  An analytical model for the heat and mass transfer processes in indirect evaporative cooling with parallel/counter flow configurations , 2006 .

[11]  Ghassem Heidarinejad,et al.  Novel modeling of an indirect evaporative cooling system with cross-flow configuration , 2015 .

[12]  Stefano De Antonellis,et al.  Desiccant wheels for air humidification: An experimental and numerical analysis , 2015 .

[13]  Stefano De Antonellis,et al.  Desiccant wheels effectiveness parameters: Correlations based on experimental data , 2015 .

[14]  P. J. Banks,et al.  A General Theory of Wet Surface Heat Exchangers and its Application to Regenerative Evaporative Cooling , 1981 .

[15]  Kyaw Thu,et al.  Study on dew point evaporative cooling system with counter-flow configuration , 2016 .

[16]  William M. Worek,et al.  Optimization of wet-surface heat exchangers , 1989 .

[17]  W. Worek,et al.  Comparison of desiccant air conditioning systems with different indirect evaporative air coolers , 2016 .

[18]  Didier Colle,et al.  Trends in worldwide ICT electricity consumption from 2007 to 2012 , 2014, Comput. Commun..

[19]  Sergey Anisimov,et al.  Performance investigation of a M (Maisotsenko)-cycle cross-flow heat exchanger used for indirect evaporative cooling , 2014 .

[20]  G. Heidarinejad,et al.  Numerical investigation of wet-bulb effectiveness and water consumption in one-and two-stage indirect evaporative coolers , 2016 .

[21]  Tianshou Zhao,et al.  A parametric study of an indirect evaporative air cooler , 1998 .

[22]  Ala Hasan,et al.  Indirect evaporative cooling : Past, present and future potentials , 2012 .