Characterizing the signal pattern of a four-cylinder diesel engine using acoustic emission and vibration analysis

Condition monitoring of diesel engines can prevent unpredicted engine failures and the associated consequence. This paper presents an experimental study of the signal characteristics of a 4-cylinder diesel engine under various loading conditions. Acoustic emission, vibration and in-cylinder pressure signals were employed to study the effectiveness of these techniques for condition monitoring and identifying symptoms of incipient failures. An event driven synchronous averaging technique was employed to average the quasi-periodic diesel engine signal in the time domain to eliminate or minimize the effect of engine speed and amplitude variations on the analysis of condition monitoring signal. It was shown that acoustic emission (AE) is a better technique than vibration method for condition monitor of diesel engines due to its ability to produce high quality signals (i.e., excellent signal to noise ratio) in a noisy diesel engine environment. It was found that the peak amplitude of AE RMS signals correlating to the impact-like combustion related events decreases in general due to a more stable mechanical process of the engine as the loading increases. A small shift in the exhaust valve closing time was observed as the engine load increases which indicates a prolong combustion process in the cylinder (to produce more power). On the contrary, peak amplitudes of the AE RMS attributing to fuel injection increase as the loading increases. This can be explained by the increase fuel friction caused by the increase volume flow rate during the injection. Multiple AE pulses during the combustion process were identified in the study, which were generated by the piston rocking motion and the interaction between the piston and the cylinder wall. The piston rocking motion is caused by the non-uniform pressure distribution acting on the piston head as a result of the non-linear combustion process of the engine. The rocking motion ceased when the pressure in the cylinder chamber stabilized.

[1]  M. Feldman,et al.  Damage Diagnosis of Rotors: Application of Hilbert Transform and Multihypothesis Testing , 1999 .

[2]  John Alexander Steel,et al.  A study of the tribological behaviour of piston ring/cylinder liner interaction in diesel engines using acoustic emission , 2006 .

[3]  A. Belmondo,et al.  Optimization of ferrographic oil analysis for diesel engine wear monitoring , 1983 .

[4]  Bo-Suk Yang,et al.  Acoustic emission for diesel engine monitoring: A review and preliminary , 2011, WCE 2011.

[5]  Lin Ma,et al.  Estimating the Loading Condition of a Diesel Engine Using Instantaneous Angular Speed Analysis , 2011, WCE 2011.

[6]  Zhihua Wang,et al.  Fault Detection in a Diesel Engine by Analysing the Instantaneous Angular Speed , 2001 .

[7]  R M Douglas,et al.  On-line power estimation of large diesel engines using acoustic emission and instantaneous crankshaft angular velocity , 2006 .

[8]  John B. Heywood,et al.  Internal combustion engine fundamentals , 1988 .

[9]  David Mba,et al.  Development of Acoustic Emission Technology for Condition Monitoring andDiagnosis of Rotating Machines; Bearings, Pumps, Gearboxes, Engines and RotatingStructures. , 2006 .

[10]  John Alexander Steel,et al.  Recent developments in monitoring of engines using acoustic emission , 2005 .

[11]  Walter Bryzik,et al.  The Frequency Analysis of the Crankshaft’s Speed Variation: A Reliable Tool for Diesel Engine Diagnosis , 2001 .

[12]  Wang Cheng-tao,et al.  An integrated on-line oil analysis method for condition monitoring , 2003 .

[13]  Andrew Ball,et al.  Detection of engine valve faults by vibration signals measured on the cylinder head , 2006 .

[14]  Stephan Ebersbach,et al.  The investigation of the condition and faults of a spur gearbox using vibration and wear debris analysis techniques , 2006 .

[15]  Antonio Paolo Carlucci,et al.  Analysis of the relation between injection parameter variation and block vibration of an internal combustion diesel engine , 2006 .

[16]  S. Hargis,et al.  Condition monitoring of marine diesel engines through ferrographic oil analysis , 1983 .

[17]  Jyoti K. Sinha,et al.  Detecting the crankshaft torsional vibration of diesel engines for combustion related diagnosis , 2009 .

[18]  Dana Combs,et al.  Piston ring cylinder liner scuffing phenomenon studies using acoustic emission technique , 2000 .

[19]  Stephen J. Citron,et al.  Cylinder-by-cylinder engine pressure and pressure torque waveform determination utilizing crankshaft speed fluctuations , 1989 .

[20]  Alberto Broatch,et al.  New methodology for in-cylinder pressure analysis in direct injection diesel engines—application to combustion noise , 2005 .

[21]  Jian Chen,et al.  Investigation into piston-slap-induced vibration for engine condition simulation and monitoring , 2005 .

[22]  Gary E. Newell Oil analysis cost‐effective machine condition monitoring technique , 1999 .