Surface defect detection in stiffened plate structures using Rayleigh-like waves

This contribution deals with the use of coupled Rayleigh-like waves for the remote detection of defects in stiffened plates similar to aerospace structures, where access is restricted by regularly spaced features such as stiffeners or stringers. Selecting appropriate excitation frequency and position, it is shown experimentally that a significant part of the energy can be transmitted past multiple obstacles, which act as a band-pass filter. Using a standard Rayleigh angle beam wedge transducer in a pulse-echo configuration, a surface defect (notch) located behind three stiffeners more than half a meter from the measurement position is detected experimentally. The detection sensitivity for different defect depths and locations relative to the structural features is discussed based on finite-difference simulations.

[1]  Irving J. Oppenheim,et al.  The transition from Lamb waves to longitudinal waves in plates , 2008 .

[2]  Masahiko Hirao,et al.  Scattering of Rayleigh surface waves by edge cracks: Numerical simulation and experiment , 1982 .

[3]  Edoardo Mazza,et al.  Analysis of the near-field ultrasonic scattering at a surface crack , 2005 .

[4]  J. Achenbach,et al.  Ray Analysis of Surface-Wave Interaction with an Edge Crack , 1980, IEEE Transactions on Sonics and Ultrasonics.

[5]  Paul Fromme,et al.  On the reflection of coupled Rayleigh-like waves at surface defects in plates. , 2008, The Journal of the Acoustical Society of America.

[6]  B. Auld,et al.  Acoustic fields and waves in solids , 1973 .

[7]  P.D. Wilcox,et al.  On the development and testing of a guided ultrasonic wave array for structural integrity monitoring , 2006, IEEE Transactions on Ultrasonics, Ferroelectrics and Frequency Control.

[8]  Yves H. Berthelot,et al.  Detection of small surface-breaking fatigue cracks in steel using scattering of Rayleigh waves , 2001 .

[9]  B. Masserey,et al.  CRACK DETECTION IN PLATES USING COUPLED RAYLEIGH‐LIKE WAVES , 2008 .

[10]  Edoardo Mazza,et al.  Ultrasonic sizing of short surface cracks. , 2007, Ultrasonics.

[11]  Laurence J. Jacobs,et al.  Propagation of guided waves in adhesive bonded components , 2002 .

[12]  G. W. Farnell,et al.  Finite Difference Analysis of Rayleigh Wave Scattering at Vertical Discontinuities , 1973 .

[13]  William D. O’Brien,et al.  Measurements of coupled Rayleigh wave propagation in an elastic plate , 1997 .

[14]  P. Fromme,et al.  Guided Ultrasonic Wave Inspection of Corrosion at Ship Hull Structures , 2006 .

[15]  I. A. Viktorov.  Rayleigh and Lamb Waves , 1967 .

[16]  Peter Cawley,et al.  The Potential of Guided Waves for Monitoring Large Areas of Metallic Aircraft Fuselage Structure , 2001 .

[17]  D Osmont,et al.  A combined finite element and modal decomposition method to study the interaction of Lamb modes with micro-defects. , 2007, Ultrasonics.

[18]  P. Cawley,et al.  The low frequency reflection characteristics of the fundamental antisymmetric Lamb wave a0 from a rectangular notch in a plate. , 2002, The Journal of the Acoustical Society of America.

[19]  T.H.G. Megson,et al.  Aircraft structures for engineering students , 1972 .

[20]  Jennifer E. Michaels,et al.  An automated time-frequency approach for ultrasonic monitoring of fastener hole cracks , 2007 .

[21]  Michel Castaings,et al.  Modal decomposition method for modeling the interaction of Lamb waves with cracks. , 2002, The Journal of the Acoustical Society of America.

[22]  P. Cawley,et al.  The interaction of Lamb waves with defects , 1992, IEEE Transactions on Ultrasonics, Ferroelectrics and Frequency Control.

[23]  P. Fromme,et al.  Measurement of the scattering of a Lamb wave by a through hole in a plate. , 2002, The Journal of the Acoustical Society of America.