Cyclic energy harvesting from pyroelectric materials

A method of continuously harvesting energy from pyroelectric materials is demonstrated using an innovative cyclic heating scheme. In traditional pyroelectric energy harvesting methods, static heating sources are used, and most of the available energy has to be harvested at once. A cyclic heating system is developed such that the temperature varies between hot and cold regions. Although the energy harvested during each period of the heating cycle is small, the accumulated total energy over time may exceed traditional methods. Three materials are studied: a commonly available soft lead zirconate titanate (PZT), a pre-stressed PZT composite, and single-crystal PMN-30PT. Radiation heating and natural cooling are used such that, at smaller cyclic frequencies, the temporal rate of change in temperature is large enough to produce high power densities. The maximum power density of 8.64 μW/cm3 is generated with a PMN-30PT single crystal at an angular velocity of 0.64 rad/s with a rate of 8.5°C/s. The pre-stressed PZT composite generated a power density of 6.31 μW/cm3, which is 40% larger than the density of 4.48 μW/cm3 obtained from standard PZT.

[1]  J. Drummond,et al.  Dielectric power conversion , 1975 .

[2]  Chul H. Park.  On the Circuit Model of Piezoceramics , 2001 .

[3]  Heath Hofmann,et al.  Adaptive piezoelectric energy harvesting circuit for wireless, remote power supply , 2001 .

[4]  Bernard H. Stark,et al.  MEMS electrostatic micropower generator for low frequency operation , 2004 .

[5]  O. P. Thakur,et al.  Dielectric, ferroelectric and pyroelectric properties of PMNT ceramics , 2006 .

[6]  Julio A. Gonzalo,et al.  Ferroelectric materials as energy converters , 1976 .

[7]  G.K. Ottman,et al.  Optimized piezoelectric energy harvesting circuit using step-down converter in discontinuous conduction mode , 2002, 2002 IEEE 33rd Annual IEEE Power Electronics Specialists Conference. Proceedings (Cat. No.02CH37289).

[8]  Neil M. White,et al.  An electromagnetic, vibration-powered generator for intelligent sensor systems , 2004 .

[9]  Joseph A. Paradiso,et al.  A Compact, Wireless, Self-Powered Pushbutton Controller , 2001, UbiComp.

[10]  G E Bertocci,et al.  A gait-powered autologous battery charging system for artificial organs. , 1995, ASAIO journal.

[11]  A. Chynoweth.  The pyroelectric behaviour of colemanite , 1957 .

[12]  S. Beeby,et al.  Energy harvesting vibration sources for microsystems applications , 2006 .

[13]  D. Guyomar,et al.  Piezoelectric Energy Harvesting Device Optimization by Synchronous Electric Charge Extraction , 2005 .

[14]  R. W. Schwartz,et al.  Development of high performance stress-biased actuators through the incorporation of mechanical pre-loads , 2002 .

[15]  Benoit Guiffard,et al.  Electrocaloric and pyroelectric properties of 0.75Pb(Mg1∕3Nb2∕3)O3–0.25PbTiO3 single crystals , 2006 .

[16]  D. Guyomar,et al.  Stability of morphotropic <110> oriented 0.65PMN-0.35PT single crystals , 2004, IEEE Transactions on Ultrasonics, Ferroelectrics and Frequency Control.

[17]  Kam K. Leang,et al.  Performance of Thin Piezoelectric Materials for Pyroelectric Energy Harvesting , 2010 .

[18]  Joseph A. Paradiso,et al.  Parasitic power harvesting in shoes , 1998, Digest of Papers. Second International Symposium on Wearable Computers (Cat. No.98EX215).

[19]  Roger W. Whatmore,et al.  Pyroelectric devices and materials , 1986 .

[20]  Daniel Guyomar,et al.  Toward Heat Energy Harvesting using Pyroelectric Material , 2009 .

[21]  Daniel J. Inman,et al.  Energy Harvesting Technologies , 2008 .

[22]  S. Priya.  Advances in energy harvesting using low profile piezoelectric transducers , 2007 .

[23]  Stephanie A. Wise,et al.  Displacement properties of RAINBOW and THUNDER piezoelectric actuators , 1998 .

[24]  Richard Heydt,et al.  Electroelastomers: applications of dielectric elastomer transducers for actuation, generation, and smart structures , 2002, SPIE Smart Structures and Materials + Nondestructive Evaluation and Health Monitoring.

[25]  Henry A. Sodano,et al.  A review of power harvesting using piezoelectric materials (2003–2006) , 2007 .

[26]  E. W. Jacobs,et al.  Pyroelectric conversion cycle of vinylidene fluoride‐trifluoroethylene copolymer , 1985 .

[27]  D. Inman,et al.  A Review of Power Harvesting from Vibration using Piezoelectric Materials , 2004 .

[28]  J. Briscoe,et al.  Pyroelectric conversion cycles , 1985 .

[29]  Daniel J. Inman,et al.  An experimental comparison between several active composite actuators for power generation , 2006 .

[30]  Harvey Thomas Banks,et al.  Evaluation criteria for THUNDER actuators , 1999, Smart Structures.

[31]  R.E. Newnham,et al.  Modeling and underwater characterization of cymbal transducers and arrays , 2001, IEEE Transactions on Ultrasonics, Ferroelectrics and Frequency Control.

[32]  Heath Hofmann,et al.  Optimized piezoelectric energy harvesting circuit using step-down converter in discontinuous conduction mode , 2003 .

[33]  Joseph A. Paradiso,et al.  Energy Scavenging with Shoe-Mounted Piezoelectrics , 2001, IEEE Micro.

[34]  J. Cooper,et al.  Minimum Detectable Power of a Pyroelectric Thermal Receiver , 1962 .

[35]  W. H. Clingman,et al.  Application of Ferroelectricity to Energy Conversion Processes , 1961 .

[36]  Paul K. Wright,et al.  A piezoelectric vibration based generator for wireless electronics , 2004 .

[37]  R. Bryant,et al.  Thin-layer composite unimorph ferroelectric driver and sensor properties , 1998 .

[38]  A. M. Glass,et al.  Principles and Applications of Ferroelectrics and Related Materials , 1977 .