Simulation model for productivity analysis of external insulated precast concrete wall system

External Insulation Finishing System (EIFS) is recognized as a suitable method for attaining energy efficiency of buildings. However, conventional EIFS is not actively applied to building construction due to additional time and cost compared with interior insulation method. Therefore, as an alternative that can contribute to active utilization of the external insulation system, this study proposes an External Insulated Precast Concrete (PC) Wall System and its simulation for performing productivity analysis. Results of this study are as follows: (1) an external insulated PC-Wall system is developed of which its insulation performance is above 40% higher than that of the conventional EIFS; (2) performance of the developed system satisfied American Standards for Testing of Materials (ASTM) and American Architectural Manufacturers Association (AAMA) standards; (3) applicability of the developed system is verified via test-bed with construction time lapsing about 40 min for each PC-Wall; and (4) CYCLONE modeling methodology is employed to perform productivity analysis of the developed system compared with conventional EIFS.

[1]  Agis M. Papadopoulos,et al.  An assessment tool for the energy, economic and environmental evaluation of thermal insulation solutions , 2009 .

[2]  Chang-Taek Hyun,et al.  Simulation-Based Schedule Estimation Model for ACS-Based Core Wall Construction of High-Rise Building , 2011 .

[3]  H. Künzel,et al.  Effect of interior and exterior insulation on the hygrothermal behaviour of exposed walls , 1998 .

[4]  Michael H. Mazor,et al.  Life Cycle Greenhouse Gas Emissions Reduction From Rigid Thermal Insulation Use in Buildings , 2011 .

[5]  Kuo-Shun Sun,et al.  Planning gang formwork operations for building construction using simulations , 2004 .

[6]  Francesco Bianchi,et al.  Insulation materials for the building sector: A review and comparative analysis , 2016 .

[7]  Chang-Sik Choi,et al.  Development and testing of precast concrete beam-to-column connections , 2013 .

[8]  Luisa F. Cabeza,et al.  New green facades as passive systems for energy savings on buildings , 2014 .

[9]  Marc Méquignon,et al.  Impact of the lifespan of different external walls of buildings on greenhouse gas emissions under tropical climate conditions , 2014 .

[10]  S. A. Al-Sanea,et al.  Effect of insulation location on thermal performance of building walls under steady periodic conditions , 2001 .

[11]  Teuku Meurah Indra Mahlia,et al.  A review on insulation materials for energy conservation in buildings , 2017 .

[12]  Taehoon Hong,et al.  An integrated evaluation of productivity, cost and CO2 emission between prefabricated and conventional columns , 2017 .

[13]  Mohammed Al-Khawaja,et al.  Determination and selecting the optimum thickness of insulation for buildings in hot countries by accounting for solar radiation , 2004 .

[14]  Roberto Garay,et al.  Experimental Thermal Performance Assessment of a Prefabricated External Insulation System for Building Retrofitting , 2017 .

[15]  David Arditi,et al.  Integrated Simulation System for Construction Operation and Project Scheduling , 2010, J. Comput. Civ. Eng..

[16]  Clay Naito,et al.  Simplified model for partially-composite precast concrete insulated wall panels subjected to lateral loading , 2017 .

[17]  Simaan M. AbouRizk,et al.  Construction project simulation using CYCLONE , 1998 .

[18]  Abang Abdullah Abang Ali,et al.  Response of precast foamed concrete sandwich panels to flexural loading , 2016 .

[19]  Ya Hong Dong,et al.  Comparing carbon emissions of precast and cast-in-situ construction methods – A case study of high-rise private building , 2015 .

[20]  Paulo Fonseca,et al.  Exterior walls covering system to improve thermal performance and increase service life of walls in rehabilitation interventions , 2017 .

[21]  Kemal Çomaklı,et al.  Optimum insulation thickness of external walls for energy saving , 2003 .

[22]  Mohammed S. Imbabi,et al.  A passive–active dynamic insulation system for all climates , 2012 .

[23]  A. Bassi,et al.  Facilitating the incorporation of VIP into precast concrete sandwich panels , 2014 .

[24]  C. Aciu,et al.  Optimal Technologies for External Thermal Insulation with Polystyrene Panels for Different Support Materials , 2015 .

[25]  Meral Ozel,et al.  Effect of insulation location on dynamic heat-transfer characteristics of building external walls and optimization of insulation thickness , 2014 .

[26]  Irving J. Oppenheim,et al.  Cracking in Exterior Insulation and Finish Systems , 1993 .

[27]  Francesca Stazi,et al.  Experimental comparison between 3 different traditional wall constructions and dynamic simulations to identify optimal thermal insulation strategies , 2013 .

[28]  Liwei Tian,et al.  Low-energy envelope design of residential building in hot summer and cold winter zone in China , 2008 .

[29]  Tahsin Başaran,et al.  Thermal performance of different exterior wall structures based on wall orientation , 2017 .

[30]  Virgo Sulakatko,et al.  Analysis of On-site Construction Processes for Effective External Thermal Insulation Composite System (ETICS) Installation☆ , 2015 .

[31]  Uniben Yao Ayikoe Tettey,et al.  Effects of different insulation materials on primary energy and CO2 emission of a multi-storey residential building , 2014 .

[32]  László Kajtár,et al.  Investment-savings method for energy-economic optimization of external wall thermal insulation thickness , 2015 .

[33]  Dionysios I. Kolaitis,et al.  Comparative assessment of internal and external thermal insulation systems for energy efficient retrofitting of residential buildings , 2013 .

[34]  José Dinis Silvestre,et al.  Comparative environmental life cycle assessment of thermal insulation materials of buildings , 2014 .

[35]  Beatriz Rodríguez-Soria,et al.  Review of international regulations governing the thermal insulation requirements of residential buildings and the harmonization of envelope energy loss , 2014 .

[36]  Bilal Akash,et al.  Some prospects of energy savings in buildings , 2001 .

[37]  Li Heng,et al.  Cost-effectiveness assessment of insulated exterior walls of residential buildings in cold climate , 2007 .