Thermal design optimization of lightweight concrete blocks for internal one-way spanning slabs floors by FEM

Abstract In the present work, numerical thermal analysis is used in order to optimize the lightweight hollow block design for internal floors with respect to the energy saving, by the finite element method (FEM). From an initial block design with 0.57 m × 0.25 m × 0.20 m constant external dimensions, other five different configurations were built varying the number the vertical and horizontal intermediate bulkheads. Besides, five different compositions of lightweight concrete have been taken into account, giving place to sixty different configurations of the floors, thirty per each heat flow direction: upward and downward heat flows. Based on the non-linear thermal analysis of the different configurations, it is possible to choose the best candidate block from the CTE rule requirements. Mathematically, the non-linearity is due to the radiation boundary condition inside the inner recesses of the blocks. Also, the temperature distribution and thermal characteristic values of the floors, both for downward and upward heat flows, are provided. From the numerical results, we can conclude that the main variables in the thermal performance are: the number of the horizontal intermediate bulkheads and the material conductivities. Therefore, increasing the number of horizontal intermediate bulkheads and decreasing the material conductivities, the best thermal efficiency is obtained. Optimization of the floors is carried out from the finite element analysis by means of the average mass overall thermal efficiency and the equivalent thermal conductivity. In order to select the appropriate floor satisfying the CTE rule requirements, detailed instructions are given. Finally, conclusions of this work are exposed.

[1]  Erdogan Madenci,et al.  The Finite Element Method and Applications in Engineering Using ANSYS , 2007 .

[2]  Ammar Bouchair,et al.  Steady state theoretical model of fired clay hollow bricks for enhanced external wall thermal insulation , 2008 .

[3]  P. J. García Nieto,et al.  Non-linear thermal optimization and design improvement of a new internal light concrete multi-holed brick walls by FEM , 2008 .

[4]  P. J. García Nieto,et al.  Non-linear thermal analysis of light concrete hollow brick walls by the finite element method and experimental validation , 2006 .

[5]  M. Modest.  Radiative heat transfer , 1993 .

[6]  W. Rohsenow,et al.  Handbook of Heat Transfer , 1998 .

[7]  O. C. Zienkiewicz,et al.  The Finite Element Method for Fluid Dynamics , 2005 .

[8]  Y. Jaluria,et al.  An Introduction to Heat Transfer , 1950 .

[9]  Teresa Gallego,et al.  Comparison of environmental impacts of building structures with in situ cast floors and with precast concrete floors , 2009 .

[10]  M. Pinar Mengüç,et al.  Thermal Radiation Heat Transfer , 2020 .

[11]  K. Bathe.  Finite Element Procedures , 1995 .

[12]  Jean-Michel Bergheau,et al.  Finite Element Simulation of Heat Transfer , 2008 .

[13]  J. M. Coulson,et al.  Heat Transfer , 2018, Finite Element Method for Solids and Structures.

[14]  F. Kreith,et al.  Principles of heat transfer , 1962 .

[15]  K. N. Seetharamu,et al.  The Finite Element Method , 2005 .

[16]  He Yongning,et al.  Optimization of the configuration of 290 140 90 hollow clay bricks with 3-D numerical simulation by finite volume method , 2008 .

[17]  R. Cook,et al.  Concepts and Applications of Finite Element Analysis , 1974 .

[18]  P. J. García Nieto,et al.  Nonlinear thermal optimization of external light concrete multi-holed brick walls by the finite element method , 2008 .

[19]  J. Reddy,et al.  The Finite Element Method in Heat Transfer and Fluid Dynamics , 1994 .

[20]  J. C. Jaeger,et al.  Conduction of Heat in Solids , 1952 .

[21]  P. J. García Nieto,et al.  Analysis and optimization of the heat-insulating light concrete hollow brick walls design by the finite element method , 2007 .

[22]  Saeed Moaveni,et al.  Finite Element Analysis Theory and Application with ANSYS , 2007 .