Finite element analysis on the anisotropic behavior of 3D printed concrete under compression and flexure

Abstract This study aims to explore effects of interfacial bond properties on the anisotropic mechanical behavior of 3D printed concrete. One finite element (FE) model which fully considered the interfacial bond properties with the traction-separation law was established and verified by the experimental results. The influence of nozzle dimensions, interfacial bond strength and concrete properties on the compressive and flexural strengths was analyzed. The results show that the horizontal shear deformation between printed filaments leads to the strength reduction for the 3D printed specimen under compression, and the tensile strength at the mid-span determines the flexural strength of 3D printed specimen. The compressive strength is relatively lower while the flexural strength is much higher for the specimens loaded in Y and Z directions. The simulation shows that the number of interfaces, the tensile and shear properties of the interface between printed filaments contribute the variation of anisotropy under compression and flexure.

[1]  Harald Kloft,et al.  Influence of process parameters on the interlayer bond strength of concrete elements additive manufactured by Shotcrete 3D Printing (SC3DP) , 2020 .

[2]  N. Roussel,et al.  Extrusion-based additive manufacturing with cement-based materials – Production steps, processes, and their underlying physics: A review , 2020, Cement and Concrete Research.

[3]  Chun’an Tang,et al.  Dynamic behavior of cement-mortar cavern reinforced by bars , 2015 .

[4]  L. P. Sanez,et al.  DISCUSSION OF EQUATION FOR THE STRESS - STRAIN CURVE OF CONCRETE’ BY DESAYI AND KRISHNAN , 1964 .

[5]  Nicolas Roussel,et al.  Weak bond strength between successive layers in extrusion-based additive manufacturing: measurement and physical origin , 2019, Cement and Concrete Research.

[6]  Guowei Ma,et al.  Mechanical characterization of 3D printed anisotropic cementitious material by the electromechanical transducer , 2018, Smart Materials and Structures.

[7]  Freek Bos,et al.  Early age mechanical behaviour of 3D printed concrete: Numerical modelling and experimental testing , 2018 .

[8]  Behrokh Khoshnevis,et al.  Effects of interlocking on interlayer adhesion and strength of structures in 3D printing of concrete , 2017 .

[9]  Tao Ding,et al.  A 3D Printed Ready-Mixed Concrete Power Distribution Substation: Materials and Construction Technology , 2019, Materials.

[10]  A. Gibb,et al.  Freeform Construction: Mega-scale Rapid Manufacturing for construction , 2007 .

[11]  Hua Li,et al.  Effects of interlayer notch and shear stress on interlayer strength of 3D printed cement paste , 2020 .

[12]  Ming Jen Tan,et al.  Additive manufacturing of geopolymer for sustainable built environment , 2017 .

[13]  G. Ma,et al.  Interlayer bonding improvement of 3D printed concrete with polymer modified mortar: Experiments and molecular dynamics studies , 2020 .

[14]  M. Tan,et al.  Rotation nozzle and numerical simulation of mass distribution at corners in 3D cementitious material printing , 2020 .

[15]  I. Saenz,et al.  Discussion of "Equation of the Stress-Strain Curve of Concrete" , 1964 .

[16]  Ming Xia,et al.  Method of enhancing interlayer bond strength in construction scale 3D printing with mortar by effective bond area amplification , 2019, Materials & Design.

[17]  Jianzhuang Xiao,et al.  Mechanical behavior of 3D printed mortar with recycled sand at early ages , 2020 .

[18]  Michael P. Case,et al.  Development of the construction processes for reinforced additively constructed concrete , 2019, Additive Manufacturing.

[19]  Jian fei Chen,et al.  Mechanical Properties of Structures 3D-Printed With Cementitious Powders , 2015, 3D Concrete Printing Technology.

[20]  A. Gibb,et al.  Hardened properties of high-performance printing concrete , 2012 .

[21]  Guangming Chen,et al.  On the finite element modelling of RC beams shear-strengthened with FRP , 2012 .

[22]  Tao Yu,et al.  Finite element modeling of confined concrete-II: Plastic-damage model , 2010 .

[23]  Freek Bos,et al.  A process classification framework for defining and describing Digital Fabrication with Concrete , 2020, Cement and Concrete Research.

[24]  Behrokh Khoshnevis,et al.  Innovative Rapid Prototyping Process Makes Large Sized, Smooth Surfaced Complex Shapes in a Wide Variety of Materials , 1998 .

[25]  L. P. Saenz Discussion of Equation for the Stress-strain Curve of Concrete by Desayi and Krishman , 1964 .

[26]  Ernst Rank,et al.  Additive manufacturing in construction: A review on processes, applications, and digital planning methods , 2019, Additive Manufacturing.

[27]  Freek Bos,et al.  Hardened properties of 3D printed concrete: The influence of process parameters on interlayer adhesion , 2019, Cement and Concrete Research.

[28]  Richard A. Buswell,et al.  Developments in construction-scale additive manufacturing processes , 2012 .

[29]  Ming Xia,et al.  Effect of surface moisture on inter-layer strength of 3D printed concrete , 2018 .

[30]  B. Panda,et al.  Measurement of tensile bond strength of 3D printed geopolymer mortar , 2018 .

[31]  Fang Wang,et al.  Mechanical anisotropy of aligned fiber reinforced composite for extrusion-based 3D printing , 2019, Construction and Building Materials.

[32]  P. Bocchini,et al.  Material characteristics of binder jet 3D printed hydrated CSA cement with the addition of fine aggregates , 2019, Construction and Building Materials.

[33]  Behrokh Khoshnevis,et al.  Interlayer adhesion and strength of structures in Contour Crafting - Effects of aggregate size, extrusion rate, and layer thickness , 2017 .

[34]  Behrokh Khoshnevis,et al.  Automated construction by contour craftingrelated robotics and information technologies , 2004 .

[35]  José Pinto Duarte,et al.  Additive manufacturing as an enabling technology for digital construction: A perspective on Construction 4.0 , 2019, Automation in Construction.

[36]  Rui Faria,et al.  An energy release rate-based plastic-damage model for concrete , 2006 .

[37]  P. Camanho,et al.  Numerical Simulation of Mixed-Mode Progressive Delamination in Composite Materials , 2003 .

[38]  Nicolas Roussel,et al.  Recent advances on yield stress and elasticity of fresh cement-based materials , 2019, Cement and Concrete Research.

[39]  Ming Jen Tan,et al.  Time gap effect on bond strength of 3D-printed concrete , 2018, Virtual and Physical Prototyping.

[40]  Tao Yu,et al.  Finite element modelling of debonding failures in steel beams flexurally strengthened with CFRP laminates , 2015 .

[41]  Lex Reiter,et al.  The role of early age structural build-up in digital fabrication with concrete , 2018, Cement and Concrete Research.

[42]  G. Ma,et al.  A novel additive mortar leveraging internal curing for enhancing interlayer bonding of cementitious composite for 3D printing , 2020 .