Vertically Integrated Double-Bridge Design for CMOS-MEMS Tri-Axial Piezo-Resistive Force Sensor

This study demonstrates a novel vertically integrated double-bridge design for tri-axial piezo-resistive force sensor using commercial available CMOS process (Fig. 1). The normal and shear force sensing capabilities are achieved by measuring the signal changes of three independent Wheatstone bridges embedded in two bridges (fixed-fixed beams). The proposed sensor design has three merits: (1) two orthogonal bridges enable the directional sensing for shear forces, (2) piezo-resistors and electrical routings embedded in two bridges are designed to form three independent Wheatstone bridges for tri-axial force sensing, (3) the footprint reduction of the sensing chip is achieved by the vertical integration of two bridges. The measurements demonstrate the feasibility of tri-axial force sensing, and indicate that the sensitivities of the proposed tri-axial force sensor are, respectively, normal force (Z-axis) −0.18 mV/N, shear force (X-axis) −7.46 mV/N, and shear force (Y-axis) 7.26 mV/N.

[1]  Weileun Fang,et al.  Inductive Micro Tri-Axial Tactile Sensor Using a CMOS Chip With a Coil Array , 2019, IEEE Electron Device Letters.

[2]  Isao Shimoyama,et al.  triaxial tactile sensor without crosstalk using pairs of piezoresistive beams ith sidewall doping , 2013 .

[3]  Weileun Fang,et al.  Design and application of a metal wet-etching post-process for the improvement of CMOS-MEMS capacitive sensors , 2009 .

[4]  Jung-Tang Huang,et al.  CMOS-MEMS piezoresistive force sensor with scanning signal process circuit for vertical probe card , 2010 .

[5]  Weileun Fang,et al.  Development of a CMOS-Based Capacitive Tactile Sensor With Adjustable Sensing Range and Sensitivity Using Polymer Fill-In , 2011, Journal of Microelectromechanical Systems.

[6]  K. Matsumoto,et al.  3D flexible tactile sensor using electromagnetic induction coils , 2012, 2012 IEEE 25th International Conference on Micro Electro Mechanical Systems (MEMS).

[7]  I. Shimoyama,et al.  MEMS on robot applications , 2009, TRANSDUCERS 2009 - 2009 International Solid-State Sensors, Actuators and Microsystems Conference.

[8]  Deqing Mei,et al.  Flexible Capacitive Tactile Sensor Array With Truncated Pyramids as Dielectric Layer for Three-Axis Force Measurement , 2015, Journal of Microelectromechanical Systems.

[9]  W. Fang,et al.  Vertically integrated CMOS-MEMS capacitive humidity sensor and a resistive temperature detector for environment application , 2017, 2017 19th International Conference on Solid-State Sensors, Actuators and Microsystems (TRANSDUCERS).

[10]  Haruo Noma,et al.  Tactile sensor array using microcantilever with nickel–chromium alloy thin film of low temperature coefficient of resistance and its application to slippage detection , 2012 .

[11]  Weileun Fang,et al.  On the detection interfaces for inductive type tactile sensors , 2019, Sensors and Actuators A: Physical.

[12]  Nguyen Binh-Khiem,et al.  High-sensitivity triaxial tactile sensor with elastic microstructures pressing on piezoresistive cantilevers , 2014 .

[13]  Weileun Fang,et al.  Vertical integration of capacitive and piezo-resistive sensing units to enlarge the sensing range of CMOS-MEMS tactile sensor , 2017, 2017 IEEE 30th International Conference on Micro Electro Mechanical Systems (MEMS).