One-dimensional thermal model for direct methanol fuel cell stacks. Part I. Model development

A thermal energy model for the direct methanol fuel cell (DMFC) is presented, based on the differential thermal energy conservation equation. The model is used to predict the thermal behaviour of a DMFC stack comprising of many large cells in a bipolar arrangement. The model allows an assessment of the effect of operating parameters (feed and oxidant inlet temperature, flow rate and pressure, operating current density), and the system design (active area, material properties and geometry) on the temperature profile along the stack and the interactions between the various components in the cell stack. The model is designed to enable the fuel cell system designer to estimate, insulation requirements, auxiliary equipment sizing and required thermal duties and response. Furthermore, the model can be used to decide on the optimum set of operating conditions for an efficient thermal management of the whole process.

[1]  Keith Scott,et al.  Performance and modelling of a direct methanol solid polymer electrolyte fuel cell , 1997 .

[2]  Keith Scott,et al.  Carbon dioxide evolution patterns in direct methanol fuel cells , 1999 .

[3]  Keith Scott,et al.  Pressure drop modelling for liquid feed direct methanol fuel cells: Part 1. Model development , 1999 .

[4]  Donald R. Glenn.  Direct fuel cell power plants : the final steps to commercialization , 1996 .

[5]  Kai Sundmacher,et al.  Direct methanol polymer electrolyte fuel cell : analysis of charge and mass transfer in the vapour-liquid-solid system , 1999 .

[6]  Angelika Heinzel,et al.  Critical issues and future prospects for solid polymer fuel cells , 1996 .

[7]  C. E. Gibbs,et al.  European opportunities for fuel cell commercialisation , 1992 .

[8]  K. Scott,et al.  Electrochemical reaction engineering , 1991 .

[9]  Christopher E. Borroni-Bird,et al.  Fuel cell commercialization issues for light-duty vehicle applications , 1996 .

[10]  Pierre R. Roberge,et al.  Parametric modelling of the performance of a 5-kW proton-exchange membrane fuel cell stack , 1994 .

[11]  Keith Scott,et al.  Material aspects of the liquid feed direct methanol fuel cell , 1998 .

[12]  T. Springer,et al.  Water Uptake by and Transport Through Nafion® 117 Membranes , 1993 .

[13]  Ralph E. White,et al.  A water and heat management model for proton-exchange-membrane fuel cells , 1993 .

[14]  J. C. Amphlett.  Performance Modeling of the Ballard Mark IV Solid Polymer Electrolyte Fuel Cell , 1995 .

[15]  J. C. Amphlett,et al.  Performance modeling of the Ballard Mark IV solid polymer electrolyte fuel cell. II: Empirical model development , 1995 .

[16]  J. M. Smith.  Chemical Engineering Kinetics , 1980 .

[17]  Keith Scott,et al.  The degree and effect of methanol crossover in the direct methanol fuel cell , 1998 .

[18]  Shimshon Gottesfeld,et al.  Direct methanol fuel cells: Developments for portable power and for potential transportation applications , 1998 .

[19]  G. Maggio,et al.  Modelling of temperature distribution in a solid polymer electrolyte fuel cell stack , 1996 .

[20]  J. H. Lee,et al.  Modeling electrochemical performance in large scale proton exchange membrane fuel cell stacks , 1998 .

[21]  T. Springer,et al.  A Comparative Study of Water Uptake By and Transport Through Ionomeric Fuel Cell Membranes , 1993 .

[22]  R. Reid,et al.  The Properties of Gases and Liquids , 1977 .

[23]  F. Melle.  The global and urban environment: the need for clean power systems , 1998 .

[24]  Keith Scott,et al.  Gas evolution and power performance in direct methanol fuel cells , 1999 .

[25]  A. J. Appleby,et al.  Characteristics of Fuel Cell Systems , 1993 .

[26]  T. Zawodzinski,et al.  The contact angle between water and the surface of perfluorosulphonic acid membranes , 1993 .

[27]  Shimshon Gottesfeld,et al.  The Water Content Dependence of Electro-Osmotic Drag in Proton-Conducting Polymer Electrolytes , 1995 .

[28]  J. C. Amphlett,et al.  A model predicting transient responses of proton exchange membrane fuel cells , 1996 .

[29]  T. Springer,et al.  Water transport properties of fuel cell ionomers , 1991 .

[30]  Musuwathi Krishnamoorthy Ravikumar,et al.  Effect of Methanol Crossover in a Liquid‐Feed Polymer‐Electrolyte Direct Methanol Fuel Cell , 1996 .

[31]  Brian E. Conway,et al.  Modern Aspects of Electrochemistry , 1974 .

[32]  Steven G. Chalk,et al.  The new generation of vehicles: market opportunities for fuel cells , 1996 .

[33]  Direct methanol fuel cell for portable applications , 1997, The Twelfth Annual Battery Conference on Applications and Advances.

[34]  J. H. Lee,et al.  Modeling fuel cell stack systems , 1998 .

[35]  JoAnn Milliken,et al.  The US Department of Energy – investing in clean transport , 1998 .

[36]  P. Christensen,et al.  Methanol Tolerant Oxygen Reduction Catalysts Based on Transition Metal Sulfides , 1998 .

[37]  Supramaniam Srinivasan,et al.  Overview of Fuel Cell Technology , 1993 .