Experimental study on hydrodynamic performances of naval propellers to adopt new additive manufacturing processes

In the past few years, a new generation of additive manufacturing (AM) techniques has rapidly become available due to the expiration of some AM patents which allowed significant cost reductions. This article explores some available techniques fostering products innovation in experimental laboratories for the development of naval propulsion, where high costs represent an important limitation for both basic research and industrial testing, by identifying significant knowledge and variables and by providing reliable and accurate data to support designers and researchers. The propeller INSEAN E779a case study was taken into account and fabricated by direct metal laser sintering in AlSi10Mg aluminium alloy and by fused deposition modeling in acrylonitrile–butadiene–styrene, and UltraT polymeric materials. The study of printing parameters, flexural tests, differential scanning calorimetry and thermogravimetric analysis, allowed to optimize the printing process conditions. A reverse engineering system, Faro-CAM2, and the iterative closest point algorithm of the geomagic control software were used to analyse deviations from the printed propeller and the CAD nominal model. The atomic force microscopy test allowed to assess the morphological features and surface roughness of printed propellers. Towing Tank tests were carried out and the hydrodynamic performance comparison was analysed in terms of torque and drag. The results of this study show differences between the benchmark and AM propellers, as a function of the advance coefficient J, the morphological characteristics and the materials. However this study also shows a substantial adequacy of AM propellers in most studies carried out in Towing Tank.

[1]  Abdolreza Simchi,et al.  On the development of direct metal laser sintering for rapid tooling , 2003 .

[2]  Christopher J. Sutcliffe,et al.  Convective heat transfer and pressure losses across novel heat sinks fabricated by Selective Laser Melting , 2009 .

[3]  Pulak M. Pandey,et al.  Influence of building strategies on the accuracy of parts in selective laser sintering , 2009 .

[4]  Antonio Lanzotti,et al.  On the Geometric Accuracy of RepRap Open-Source Three-Dimensional Printer , 2015 .

[5]  Antonio Lanzotti,et al.  Understanding Process Parameter Effects of RepRap Open-Source Three-Dimensional Printers Through a Design of Experiments Approach , 2015 .

[6]  Li Lu,et al.  Direct metal laser sintering for rapid tooling: processing and characterisation of EOS parts , 2001 .

[7]  Y. Song,et al.  Experimental Study of the Basic Process Mechanism for Direct Selective Laser Sintering of Low-Melting Metallic Powder , 1997 .

[8]  Irene Penesis,et al.  Model testing and performance comparison of plastic and metal tidal turbine rotors , 2015 .

[9]  Joaquim Ciurana,et al.  Influence of process parameters on part quality and mechanical properties for DMLS and SLM with iron-based materials , 2012 .

[10]  Paul J. Besl,et al.  A Method for Registration of 3-D Shapes , 1992, IEEE Trans. Pattern Anal. Mach. Intell..

[11]  F. Calignano,et al.  Influence of process parameters on surface roughness of aluminum parts produced by DMLS , 2012, The International Journal of Advanced Manufacturing Technology.

[12]  M. Fantini,et al.  Design and Rapid Manufacturing of anatomical prosthesis for facial rehabilitation , 2013 .

[13]  M. Martorelli,et al.  The impact of process parameters on mechanical properties of parts fabricated in PLA with an open-source 3-D printer , 2015 .

[14]  T. Breteau,et al.  Design for manufacturing with tool paths adapted to marine propeller , 2011 .

[15]  Thomas Grünberger,et al.  Direct Metal Laser Sintering , 2015 .

[16]  Wei Wang,et al.  Selective laser melting of AlSi10Mg alloy: Process optimisation and mechanical properties development , 2015, Materials & Design (1980-2015).

[17]  Salvatore Gerbino,et al.  On the influence of scanning factors on the laser scanner-based 3D inspection process , 2016 .

[18]  Gianluca D’Antonio,et al.  Enriching design with X through tailored additive manufacturing knowledge : a methodological proposal , 2017 .