Simulating Cavitation and Hydraulic Flip Inside Hydroentangling Nozzles

Hydroentangling owes its success to the peculiar properties of coherent water jets. For hydroentangling to be feasible at higher pressures, it is extremely important that water jets maintain their collimation for an appreciable distance downstream of the nozzle. How ever, water-jet breakup accelerates at high pressures. Recent studies have shown that cavitation severely affects the integrity of high-pressure water jets. Investigating cavita tion experimentally is not trivial. Computational fluid dynamics simulations offer appro priate tools as a first step. This paper discusses the results of an unsteady-state simulation, which shows the inception and time-evolution of a cavitation cloud inside a hydroentan gling nozzle. Under certain conditions, the cavity cloud extends to the nozzle outlet, resulting in the so-called hydraulic flip. Once hydraulic flip occurs, cavitation suddenly vanishes because the downstream air moves upward into the nozzle and fills the cavity. This air envelops the water flow inside the nozzle, which results in the depletion of cavitation-induced instabilities from the jet surface and elongates the jet breakup length. Moreover, our simulations reveal the approximate time scales of cavity growth through the nozzle. This information is highly relevant for experimental visualization of nozzle cavitation. The discharge and velocity coefficient obtained from the simulation are in a good agreement with published experimental data.

[1]  Masanori Shimizu,et al.  Enhancement of the atomization of a liquid jet by cavitation in a nozzle hole , 2001 .

[2]  S. Heister,et al.  Modeling Cavitating Venturi Flows , 2002 .

[3]  Alfred Leipertz,et al.  Investigation of cavitation in real size diesel injection nozzles , 1999 .

[4]  Arthur H. Lefebvre,et al.  GEOMETRICAL EFFECTS ON DISCHARGE COEFFICIENTS FOR PLAIN-ORIFICE ATOMIZERS , 1991 .

[5]  Stephen D. Heister,et al.  CAVITATING INJECTOR FLOWS: VALIDATION OF NUMERICAL MODELS AND SIMULATIONS OF PRESSURE ATOMIZERS , 1999 .

[6]  K. Ramamurthi,et al.  Characteristics of flow through small sharp-edged cylindrical orifices , 1999 .

[7]  Christopher J. Rutland,et al.  Cavitation in Two-Dimensional Asymmetric Nozzles , 1999 .

[8]  Masanori Shimizu,et al.  EFFECTS OF CAVITATION AND INTERNAL FLOW ON ATOMIZATION OF A LIQUID JET , 1998 .

[9]  Manolis Gavaises,et al.  Analysis of the Flow in the Nozzle of a Vertical Multi-Hole Diesel Engine Injector , 1998 .

[10]  Hiroyuki Hiroyasu,et al.  SPRAY BREAKUP MECHANISM FROM THE HOLE-TYPE NOZZLE AND ITS APPLICATIONS , 2000 .

[11]  K. Ramamurthi,et al.  Influence of periodic disturbances on inception of cavitation in sharp-edged orifices , 2002 .

[12]  F. Obermeier,et al.  EXPERIMENTAL STUDY OF CAVITATION IN THE NOZZLE HOLE OF DIESEL INJECTORS USING TRANSPARENT NOZZLES , 1995 .

[13]  Weeratunge Malalasekera,et al.  An introduction to computational fluid dynamics - the finite volume method , 2007 .

[14]  Roger E. A. Arndt,et al.  Numerical Modeling of Sheet and Tip Vortex Cavitation with Fluent 5 , 2001 .

[15]  Olivier Simonin,et al.  Numerical Simulation of Cavitating Flows in Diesel Injectors by a Homogeneous Equilibrium Modeling Approach , 2001 .

[16]  B. Pourdeyhimi,et al.  The effects of nozzle geometry on waterjet breakup at high Reynolds numbers , 2003 .

[17]  B. Pourdeyhimi,et al.  Effect of Nozzle Geometry on Hydroentangling Water Jets: Experimental Observations , 2004 .

[18]  H. Tafreshi,et al.  Simulating and Characterizing Water Flows Inside Hydroentangling Orifices , 2003 .

[19]  Simulating the Flow Dynamics in Hydroentangling Nozzles: Effect of Cone Angle and Nozzle Aspect Ratio , 2003 .