Improving the 3D printability of high volume fly ash mixtures via the use of nano attapulgite clay

Abstract The effect of nano-attapulgite clay (NC) addition on the fresh, hardened and microstructural properties of high volume fly ash (HVFA) mixes designed for 3D printing was investigated in this study. Experimental results showed that the addition of 0.1–0.5% (i.e. by mass of binder) NC increased the static yield stress of HVFA mortars without significantly affecting the apparent viscosity, due to particle re-flocculation and enhanced thixotropy. When compared to the control mix, the use of 0.5% NC also led to increased viscosity recovery and improved structural build-up at different resting times and shear rates. These advancements were useful for 3D concrete printing, during which the material should be extrudable and buildable layer-by-layer without any deformation. Successful implementation of mixes containing NC was demonstrated via the printing of a 20-layer structure. Further optimization of the NC content and associated HVFA mix design is recommended, depending on the geometrical and mechanical properties required.

[1]  J. Ou,et al.  Microstructure of cement mortar with nano-particles , 2004 .

[2]  N. Neithalath,et al.  Mechanical and microstructural characterization of alkali sulfate activated high volume fly ash binders , 2017 .

[3]  Freek Bos,et al.  Early age mechanical behaviour of 3D printed concrete: Numerical modelling and experimental testing , 2018 .

[4]  Behrokh Khoshnevis,et al.  Cementitious materials for construction-scale 3D printing: Laboratory testing of fresh printing mixture , 2017 .

[5]  Fernando Fraternali,et al.  On the reinforcement of cement mortars through 3D printed polymeric and metallic fibers , 2016 .

[6]  David V. Boger,et al.  Yield stress measurements with the vane , 1996 .

[7]  B. Panda,et al.  Measurement of tensile bond strength of 3D printed geopolymer mortar , 2018 .

[8]  Ye Qian,et al.  Enhancing thixotropy of fresh cement pastes with nanoclay in presence of polycarboxylate ether superplasticizer (PCE) , 2018, Cement and Concrete Research.

[9]  Ye Qian,et al.  Experimental and modeling study on the non-linear structural build-up of fresh cement pastes incorporating viscosity modifying admixtures , 2018, Cement and Concrete Research.

[10]  Nicolas Roussel,et al.  Rheological requirements for printable concretes , 2018, Cement and Concrete Research.

[11]  W. Haden.  Attapulgite: Properties and Uses , 1961 .

[12]  Ming Jen Tan,et al.  Additive manufacturing of geopolymer for sustainable built environment , 2017 .

[13]  Hamlin M. Jennings,et al.  The influence of mixing on the rheology of fresh cement paste , 1999 .

[14]  Ming Jen Tan,et al.  Experimental study on mix proportion and fresh properties of fly ash based geopolymer for 3D concrete printing , 2018, Ceramics International.

[15]  Kah Fai Leong,et al.  3D printing trends in building and construction industry: a review , 2017 .

[16]  Elena Fuente,et al.  Aggregation and breakage kinetics of fresh cement paste , 2013 .

[17]  Mohend Chaouche,et al.  Rate of thixotropic rebuilding of cement pastes modified with highly purified attapulgite clays , 2013 .

[18]  T. T. Le,et al.  Mix design and fresh properties for high-performance printing concrete , 2012 .

[19]  N. Roussel,et al.  Distinct-layer casting of SCC: The mechanical consequences of thixotropy , 2008 .

[20]  Colangelo,et al.  Alkali activated waste fly ash as sustainable composite: Influence of curing and pozzolanic admixtures on the early-age physico-mechanical properties and residual strength after exposure at elevated temperature , 2018 .

[21]  Clément Gosselin,et al.  Large-scale 3D printing of ultra-high performance concrete – a new processing route for architects and builders , 2016 .

[22]  D. Cheng.  Yield stress: A time-dependent property and how to measure it , 1986 .

[23]  Faiz Shaikh,et al.  Characterizations of flax fabric reinforced nanoclay-geopolymer composites , 2016 .

[24]  Chung R. Song,et al.  A molecular dynamics and microporomechanics study on the mechanical properties of major constituents of hydrated cement , 2010 .

[25]  Nathan Tregger,et al.  Influence of clays on the rheology of cement pastes , 2010 .

[26]  Kejin Wang,et al.  Effects of Nanomaterials on the Hydration Kinetics and Rheology of Portland Cement Pastes , 2015 .

[27]  A. Kashani,et al.  Additive manufacturing (3D printing): A review of materials, methods, applications and challenges , 2018, Composites Part B: Engineering.

[28]  Ming Jen Tan,et al.  Investigation of the rheology and strength of geopolymer mixtures for extrusion-based 3D printing , 2018, Cement and Concrete Composites.

[29]  David J. Corr,et al.  Study of the mechanisms underlying the fresh-state response of cementitious materials modified with nanoclays , 2012 .

[30]  Zhihui Sun,et al.  Rheological Method to Evaluate Structural Buildup in Self-Consolidating Concrete Cement Pastes , 2007 .

[31]  Nicolas Roussel,et al.  The origins of thixotropy of fresh cement pastes , 2012 .

[32]  Jinhui Li,et al.  A new computational approach for estimation of wilting point for green infrastructure , 2017 .

[33]  Surendra P. Shah,et al.  Modification of cement-based materials with nanoparticles , 2013 .

[34]  Nicolas Roussel,et al.  A thixotropy model for fresh fluid concretes: Theory, validation and applications , 2006 .

[35]  Ammar Yahia,et al.  Field-oriented test methods to evaluate structural build-up at rest of flowable mortar and concrete , 2012 .