Recognition of Acoustic Signals of Synchronous Motors with the Use of MoFS and Selected Classifiers

Abstract This paper proposes an approach based on acoustic signals for detecting faults appearing in synchronous motors. Acoustic signals of a machine were used for fault detection. These faults contained: broken coils and shorted stator coils. Acoustic signals were used to assess the usefulness of early fault diagnostic of synchronous motors. The acoustic signal recognition system was based on methods of data processing: normalization of the amplitude, Fast Fourier Transform (FFT), method of frequency selection (MoFS), backpropagation neural network, classifier based on words coding, and Nearest Neighbor classifier. A plan of study of acoustic signals of synchronous motors was proposed. Software of acoustic signal recognition of synchronous motors was implemented. Four states of a synchronous motor were used in analysis. A pattern creation process was carried out for 28 training samples of noise. An identification process was carried out for 60 test samples. This system can be used to diagnose synchronous motors and other electrical machines.

[1]  Artur Polak,et al.  Selected diagnostic methods of electrical machines operating in industrial conditions , 2014, IEEE Transactions on Dielectrics and Electrical Insulation.

[2]  Philip J. B. Jackson,et al.  Two-Microphone Dereverberation for Automatic Speech Recognition of Polish , 2015 .

[3]  Adam Glowacz,et al.  Diagnostics of Synchronous Motor Based on Analysis of Acoustic Signals with the use of Line Spectral Frequencies and K-nearest Neighbor Classifier , 2015 .

[4]  K. Stępień,et al.  Research on a surface texture analysis by digital signal processing methods , 2014 .

[5]  Piotr Augustyniak,et al.  Seamless Tracing of Human Behavior Using Complementary Wearable and House-Embedded Sensors , 2014, Sensors.

[6]  Eduardo Carlos Bianchi,et al.  Tool condition monitoring of aluminum oxide grinding wheel in dressing operation using acoustic emission and neural networks , 2015 .

[7]  Chen Lu,et al.  MACHINE INTEGRATED HEALTH MODELS FOR CONDITION-BASED MAINTENANCE , 2014 .

[8]  M. Sulowicz,et al.  A Distributed System of Signal Acquisition for Induction Motors Diagnostic , 2007, 2007 IEEE International Symposium on Diagnostics for Electric Machines, Power Electronics and Drives.

[9]  Stanislaw Legutko,et al.  Investigations Into Surface Integrity in the Turning Process of Duplex Stainless Steel , 2014 .

[10]  Liang Ma,et al.  Fault diagnosis approach for rotating machinery based on dynamic model and computational intelligence , 2015 .

[11]  Matej Kucera,et al.  Diagnostics of electric equipments by means of thermovision , 2011 .

[12]  Stanislaw Legutko,et al.  Effect of the disc processing technology on the vibration level of the chipper during operations , 2014 .

[13]  Gevork B. Gharehpetian,et al.  Locating Pd in Transformers through Detailed Model and Neural Networks , 2014 .

[14]  Bozena Kostek,et al.  Classification of Music Genres Based on Music Separation into Harmonic and Drum Components , 2015 .

[15]  Jiří Přibil,et al.  Mapping and Spectral Analysis of Acoustic Vibration in the Scanning Area of the Weak Field Magnetic Resonance Imager , 2014 .

[16]  Adam Glowacz,et al.  Recognition of Monochrome Thermal Images of Synchronous Motor with the Application of Skeletonization and Classifier Based on Words , 2015 .

[17]  Bo Wang,et al.  Fault diagnosis of rolling bearing based on relevance vector machine and kernel principal component analysis , 2014 .

[18]  Yagang Zhang,et al.  LATEST PROGRESS OF FAULT DETECTION AND LOCALIZATION IN COMPLEX ELECTRICAL ENGINEERING , 2014 .

[19]  Jolanta B. Krolczyk,et al.  THE USE OF THE CLUSTER ANALYSIS METHOD TO DESCRIBE THE MIXING PROCESS OF THE MULTI-ELEMENT GRANULAR MIXTURE , 2015 .

[20]  Yu-Ling He,et al.  Investigation on stator vibration characteristics under air-gap eccentricity and rotor short circuit composite faults , 2014 .

[21]  Adam Glowacz,et al.  Recognition of Color Thermograms of Synchronous Motor with the Application of Image Cross-Section and Linear Perceptron Classifier , 2012 .

[22]  M. R. Aghamohammadi,et al.  Development and implementation of neural network observers to estimate synchronous generators’ dynamic parameters using on-line operating data , 2014 .

[23]  Adam Glowacz.  Diagnostics of direct current machine based on analysis of acoustic signals with the use of symlet wavelet transform and modified classifier based on words , 2014 .

[24]  Orest Kochan,et al.  Investigations of Thermocouple Drift Irregularity Impact on Error of their Inhomogeneity Correction , 2014 .

[25]  Ryszard Tadeusiewicz,et al.  Approximation of phenol concentration using novel hybrid computational intelligence methods , 2014, Int. J. Appl. Math. Comput. Sci..

[26]  Ninoslav Zuber,et al.  Gearbox faults identification using vibration signal analysis and artificial intelligence methods , 2014 .

[27]  Dariusz Pleban.  Definition and Measure of the Sound Quality of the Machine , 2015 .

[28]  Zbigniew Kulka,et al.  Advances in Digitization of Microphones and Loudspeakers , 2011 .

[29]  A. Smalcerz,et al.  Aspects of application of industrial robots in metallurgical processes , 2013 .

[30]  Dariusz MAzurkiewicz.  Computer-aided maintenance and reliability management systems for conveyor belts , 2014 .

[31]  Huseyin Ekiz,et al.  A neural network based approach to estimate of power system harmonics for an induction furnace under the different load conditions , 2015 .

[32]  David VAlis.  Utilization of diffUsion processes and fUzzy logic for vUlnerability assessment Wykorzystanie procesó W dyfUzyjnych i logiki rozmytej do oceny podatności na zagrożenie , 2014 .

[33]  Joanna Jaworek-Korjakowska,et al.  Determination of border irregularity in dermoscopic color images of pigmented skin lesions , 2014, 2014 36th Annual International Conference of the IEEE Engineering in Medicine and Biology Society.

[34]  Kristian Sabo,et al.  ACOUSTIC EMISSION AS TOOL WEAR MONITORING , 2014 .

[35]  Viet Phuong Bui,et al.  Noninvasive Fault Monitoring of Electrical Machines by Solving the Steady-State Magnetic Inverse Problem , 2008 .

[36]  Jian Xiao,et al.  Fault diagnosis for rotating machinery based on multi-differential empirical mode decomposition , 2014 .

[37]  Edward Nawarecki,et al.  Multi-aspect Character of the Man-Computer Relationship in a Diagnostic-Advisory System , 2012 .

[38]  Marek R. Ogiela,et al.  Application of neural networks in detection of abnormal brain perfusion regions , 2013, Neurocomputing.

[39]  Stanislawa Kluska-Nawarecka,et al.  Computer-Assisted Integration of Knowledge in the Context of Identification of the Causes of Defects in Castings , 2014 .

[40]  Idriss El-Thalji,et al.  A summary of fault modelling and predictive health monitoring of rolling element bearings , 2015 .

[41]  J. Roj,et al.  Neural Network Based Real-time Correction of Transducer Dynamic Errors , 2013 .

[42]  I. R. Praveen Krishna,et al.  Local fault detection in helical gears via vibration and acoustic signals using EMD based statistical parameter analysis , 2014 .

[43]  Myeongsu Kang,et al.  Reliable Fault Diagnosis for Low-Speed Bearings Using Individually Trained Support Vector Machines With Kernel Discriminative Feature Analysis , 2015, IEEE Transactions on Power Electronics.

[44]  Jiÿr ´ õ Pÿribil,et al.  EVALUATION OF SPECTRAL AND PROSODIC FEATURES OF SPEECH AFFECTED BY ORTHODONTIC APPLIANCES USING THE GMM CLASSIFIER , 2014 .

[45]  Sławomir Wierzbicki,et al.  Application of vibration signal in the diagnosis of IC engine valve clearance , 2015 .

[46]  Stanislawa Kluska-Nawarecka,et al.  Methodology for the Construction of a Rule-Based Knowledge Base Enabling the Selection of Appropriate Bronze Heat Treatment Parameters Using Rough Sets , 2015 .