Effect of microstructure evolution on chip formation and fracture during high-speed cutting of single phase metals

[1]  Zhanqiang Liu,et al.  Evolutions of grain size and micro-hardness during chip formation and machined surface generation for Ti-6Al-4V in high-speed machining , 2016 .

[2]  S. V. Subramanian,et al.  Effect of microstructure softening events on the chip morphology of AISI 1045 steel during high speed machining , 2016 .

[3]  Bing Wang,et al.  Brittle Removal Mechanism of Ductile Materials With Ultrahigh-Speed Machining , 2015 .

[4]  Liang Li,et al.  Investigation on the influence of material microstructure on cutting force and bur formation in the micro cutting of copper , 2015 .

[5]  Zhanqiang Liu,et al.  Influences of chip serration on micro-topography of machined surface in high-speed cutting , 2015 .

[6]  S. Melkote,et al.  A unified material model including dislocation drag and its application to simulation of orthogonal cutting of OFHC Copper , 2015 .

[7]  Lanhong Dai,et al.  Critical cutting speed for onset of serrated chip flow in high speed machining , 2014 .

[8]  Yi-long Bai,et al.  Introduction To Adiabatic Shear Localization , 2014 .

[9]  J. Jonas,et al.  Dynamic and post-dynamic recrystallization under hot, cold and severe plastic deformation conditions , 2014 .

[10]  Kyung-Tae Park,et al.  Dynamic tensile extrusion behavior of coarse grained and ultrafine grained OFHC Cu , 2013 .

[11]  Alain Molinari,et al.  Strain, strain rate and velocity fields determination at very high cutting speed , 2013 .

[12]  G. List,et al.  Very high speed cutting of Ti–6Al–4V titanium alloy – change in morphology and mechanism of chip formation , 2013 .

[13]  Jun Zhao,et al.  Experimental investigation on chip morphologies in high-speed dry milling of titanium alloy Ti-6Al-4V , 2012 .

[14]  Liu Zhanqiang,et al.  Characteristics of chip evolution with elevating cutting speed from low to very high , 2012 .

[15]  Chunzheng Duan,et al.  Adiabatic shear banding in AISI 1045 steel during high speed machining: Mechanisms of microstructural evolution , 2012 .

[16]  Ricardo A. Lebensohn,et al.  Effects of grain size and boundary structure on the dynamic tensile response of copper , 2011 .

[17]  Christopher Saldana,et al.  Controlling deformation and microstructure on machined surfaces , 2011 .

[18]  T. Hua,et al.  Study on constitutive relations and spall models for oxygen-free high-conductivity copper under planar shock tests , 2007 .

[19]  Jihong Hwang,et al.  Large strain deformation field in machining , 2006 .

[20]  Z. G. Wang,et al.  A Review on High-Speed Machining of Titanium Alloys ∗ , 2006 .

[21]  Yuebin Guo,et al.  A FEM study on mechanisms of discontinuous chip formation in hard machining , 2004 .

[22]  A. Schwartz,et al.  Effect of microstructural length scales on spall behavior of copper , 2004 .

[23]  P. Chevrier,et al.  Investigation of surface integrity in high speed end milling of a low alloyed steel , 2003 .

[24]  Mohamed A. Elbestawi,et al.  From the basic mechanics of orthogonal metal cutting toward the identification of the constitutive equation , 2002 .

[25]  Marc A. Meyers,et al.  DYNAMIC RECRYSTALLIZATION IN HIGH-STRAIN, HIGH-STRAIN-RATE PLASTIC DEFORMATION OF COPPER , 1994 .

[26]  M. J. Luton,et al.  The effect of nucleation models on dynamic recrystallization II. Heterogeneous stored-energy distribution , 1993 .

[27]  Brian Derby,et al.  The dependence of grain size on stress during dynamic recrystallisation , 1991 .

[28]  J. E. Bailey,et al.  The recrystallization process in some polycrystalline metals , 1962, Proceedings of the Royal Society of London. Series A. Mathematical and Physical Sciences.

[29]  Guillaume Fromentin,et al.  Orthogonal Cutting Simulation of OFHC Copper Using a New Constitutive Model Considering the State of Stress and the Microstructure Effects , 2016 .

[30]  Christian Brecher,et al.  Chatter suppression techniques in metal cutting , 2016 .

[31]  Jun Zhang,et al.  Investigation on Morphological Evolution of Chips for Ti6Al4V Alloys with the Increasing Milling Speed , 2016 .

[32]  S. Chandrasekar,et al.  Control of deformation levels on machined surfaces , 2011 .

[33]  Christopher Saldana,et al.  Controlling gradation of surface strains and nanostructuring by large-strain machining , 2009 .

[34]  B. H. Sassi,et al.  Effect of the cutting speed on the chip morphology and the cutting forces , 2009 .

[35]  L. Roesch,et al.  Relationship Between Precipitation and Dimple Fracture in an 18 Percent Nickel Maraging Steel , 1969 .