Chemical liquid-phase detection using guided SH-SAW: theoretical simulation and experiments

Results are presented for direct chemical sensing in liquid environments using guided shear horizontal surface acoustic wave (SH-SAW) sensor platforms on 36/spl deg/ rotated Y-cut LiTaO/sub 3/. Two different sensor geometries are theoretically analyzed. Complex bulk and shear moduli are utilized to represent the viscoelastic properties of the polymers and estimate their influence on the velocity shift and attenuation change, hence on the sensor characteristics. Experimental results are presented and discussed for dual delay line devices with a reference line coated with PMMA and a sensing line coated with a chemically sensitive polymer, which acts as both a guiding layer and a sensing layer. Various chemically sensitive polymers are investigated, and the tested analytes include toluene, ethylbenzene and xylene. Analytes in the low concentration (1 ppm to 60 ppm) range in aqueous solutions are tested. Stability, sensitivity and partial selectivity are investigated by varying the coating thickness and curing temperature for the chemically sensitive layer. Partition coefficients for polymer-aqueous analyte pairs are used to explain the observed trend in sensitivity. Both mass loading and the coating viscoelasticity change influence the sensor response. A low ppb level detection limit is estimated from the present experiment measurement.

[1]  F Bender,et al.  Guided shear horizontal surface acoustic wave sensors for chemical and biochemical detection in liquids. , 2001, Analytical chemistry.

[2]  Electra Gizeli,et al.  Modelling of the mass sensitivity of the Love wave device in the presence of a viscous liquid , 2000 .

[3]  Patel,et al.  Real-time detection of organic compounds in liquid environments using polymer-coated thickness shear mode quartz resonators , 2000, Analytical chemistry.

[4]  Florian Bender,et al.  Love-Wave Biosensors Using Cross-Linked Polymer Waveguides on LiTaO{sub 3} Substrates , 2000 .

[5]  J. Grate,et al.  The fractional free volume of the sorbed vapor in modeling the viscoelastic contribution to polymer-coated surface acoustic wave vapor sensor responses. , 2000, Analytical chemistry.

[6]  S. Shiokawa,et al.  Simulation of Viscoelastic Effects of Polymer Coatings on Surface Acoustic Wave Gas Sensor under Consideration of Film Thickness. , 1998 .

[7]  Nathali Kaushansky,et al.  The polymer-coated SAW sensor as a gravimetric sensor , 1997 .

[8]  G. L. Harding,et al.  Love wave acoustic immunosensor operating in liquid , 1997 .

[9]  Stephen J. Martin,et al.  Acoustic Wave Sensors: Theory, Design and Physico-Chemical Applications , 1996 .

[10]  S. Shiokawa,et al.  Simultaneous Measurements of Liquid Properties Using Multichannel Shear Horizontal Surface Acoustic Wave Microsensor. , 1996 .

[11]  Jay W. Grate,et al.  Method for Estimating Polymer-Coated Acoustic Wave Vapor Sensor Responses , 1995 .

[12]  Stephen J. Martin,et al.  Dynamics and Response of Polymer-Coated Surface Acoustic Wave Devices: Effect of Viscoelastic Properties and Film Resonance , 1994 .

[13]  R. A. McGill,et al.  The predominant role of swelling-induced modulus changes of the sorbent phase in determining the responses of polymer-coated surface acoustic wave vapor sensors , 1992 .

[14]  J. Grate,et al.  Comparisons of polymer/gas partition coefficients calculated from responses of thickness shear mode and surface acoustic wave vapor sensors. , 1998, Analytical chemistry.

[15]  David S. Ballantine,et al.  Acoustic wave sensors : theory, design, and physico-chemical applications , 1997 .

[16]  R. A. McGill,et al.  CHOOSING POLYMER COATINGS FOR CHEMICAL SENSORS , 1994 .

[17]  S. Shiokawa,et al.  A liquid sensor based on a shear horizontal saw device , 1993 .