Melt pool simulation for the evaluation of process parameters in selective laser melting

Abstract With increasing industrial interest and significance of the selective laser melting the importance for profound process knowledge increases so that new materials can be qualified faster. Also it is the basis for an educated evaluation of possible process innovations. Therefore a 3D numerical model for the selective laser melting process is presented that allows a detailed look into the process dynamics at comparably low calculation effort. It combines a finite difference method with a combined level set volume of fluid method for the simulation of the process and starts with a homogenized powder bed in its initial configuration. The model uses a comprehensive representation of various physical effects like dynamic laser power absorption, buoyancy effect, Marangoni effect, capillary effect, evaporation, recoil pressure and temperature dependent material properties. It is validated for different process parameters using cubic samples of stainless steel 316L and nickel-based superalloy IN738LC. The results show the significance of evaporation and its related recoil pressure for a feasible prediction of the melt pool dynamics. Furthermore a possible way to reduce the times and costs for material qualification by using the simulation model to predict possible process parameters and therefore to reduce the necessary experimental effort for material qualification to a minimum is shown.

[1]  E. Brandl,et al.  Additive manufactured AlSi10Mg samples using Selective Laser Melting (SLM): Microstructure, high cycle fatigue, and fracture behavior , 2012 .

[2]  J. Mazumder,et al.  Modeling of laser keyhole welding: Part I. mathematical modeling, numerical methodology, role of recoil pressure, multiple reflections, and free surface evolution , 2002 .

[3]  S. Khairallah,et al.  Mesoscopic Simulation Model of Selective Laser Melting of Stainless Steel Powder , 2014 .

[4]  K. Wegener,et al.  High temperature material properties of IN738LC processed by selective laser melting (SLM) technology , 2013 .

[5]  Richard M. Everson,et al.  Finite element simulation of the temperature and stress fields in single layers built without-support in selective laser melting , 2013 .

[6]  R. J. Bell,et al.  Optical properties of Au, Ni, and Pb at submillimeter wavelengths. , 1987, Applied optics.

[7]  S. Ko,et al.  Mechanism of keyhole formation and stability in stationary laser welding , 2002 .

[8]  Tom Craeghs,et al.  A pragmatic model for selective laser melting with evaporation , 2009 .

[9]  G. Son.  A LEVEL SET METHOD FOR INCOMPRESSIBLE TWO-FLUID FLOWS WITH IMMERSED SOLID BOUNDARIES , 2005 .

[10]  Gihun Son,et al.  EFFICIENT IMPLEMENTATION OF A COUPLED LEVEL-SET AND VOLUME-OF-FLUID METHOD FOR THREE-DIMENSIONAL INCOMPRESSIBLE TWO-PHASE FLOWS , 2003 .

[11]  Joel W. Barlow,et al.  The Prediction of the Emissivity and Thermal Conductivity of Powder Beds , 2004 .

[12]  J. Kruth,et al.  Modelling of radiation transfer in metallic powders at laser treatment , 2005 .

[13]  Matej Praprotnik,et al.  INHOMOGENEOUS HEAT-CONDUCTION PROBLEMS SOLVED BY A NEW EXPLICIT FINITE DIFFERENCE SCHEME , 2004 .

[14]  Carolin Körner,et al.  Evaporation model for beam based additive manufacturing using free surface lattice Boltzmann methods , 2014 .

[15]  Jerome Solberg,et al.  Implementation of a thermomechanical model for the simulation of selective laser melting , 2014 .

[16]  C. Arvieu,et al.  Numerical modeling of inconel 738LC deposition welding: Prediction of residual stress induced cracking , 2010 .

[17]  Chandrika Kamath,et al.  Observation of keyhole-mode laser melting in laser powder-bed fusion additive manufacturing , 2014 .

[18]  H. Fraser,et al.  Effects of process variables and size-scale on solidification microstructure in beam-based fabrication of bulky 3D structures , 2009 .

[19]  A. Gosman,et al.  Solution of the implicitly discretised reacting flow equations by operator-splitting , 1986 .

[20]  R. Poprawe,et al.  Selective Laser Melting of in-situ TiC/Ti5Si3 composites with novel reinforcement architecture and elevated performance , 2011 .

[21]  Andrey V. Gusarov,et al.  Model of Radiation and Heat Transfer in Laser-Powder Interaction Zone at Selective Laser Melting , 2009 .

[22]  Leon L. Shaw,et al.  Distortion minimization of laser‐processed components through control of laser scanning patterns , 2002 .

[23]  D. Gu,et al.  Tailoring surface quality through mass and momentum transfer modeling using a volume of fluid method in selective laser melting of TiC/AlSi10Mg powder , 2015 .

[24]  M. Ramulu,et al.  Fatigue performance evaluation of selective laser melted Ti–6Al–4V , 2014 .

[25]  Christ Glorieux,et al.  Photopyroelectric measurement of thermal conductivity of metallic powders , 2005 .

[26]  L. Froyen,et al.  Fundamentals of Selective Laser Melting of alloyed steel powders , 2006 .

[27]  Wei Zhang,et al.  Modeling of heat transfer, fluid flow and solidification microstructure of nickel-base superalloy fabricated by laser powder bed fusion , 2016 .

[28]  Franz Sebastian Schwindling,et al.  Two-Body Wear of CoCr Fabricated by Selective Laser Melting Compared with Different Dental Alloys , 2015, Tribology Letters.

[29]  R. J. Bell,et al.  Optical properties of fourteen metals in the infrared and far infrared: Al, Co, Cu, Au, Fe, Pb, Mo, Ni, Pd, Pt, Ag, Ti, V, and W. , 1985, Applied optics.

[30]  Ming Gao,et al.  The microstructure and mechanical properties of deposited-IN718 by selective laser melting , 2012 .

[31]  A. Rubenchik,et al.  Laser powder-bed fusion additive manufacturing: Physics of complex melt flow and formation mechanisms of pores, spatter, and denudation zones , 2015, 1512.02593.

[32]  Nahmkeon Hur,et al.  A COUPLED LEVEL SET AND VOLUME-OF-FLUID METHOD FOR THE BUOYANCY-DRIVEN MOTION OF FLUID PARTICLES , 2002 .

[33]  Reinhart Poprawe,et al.  Formation and reduction of hydrogen porosity during selective laser melting of AlSi10Mg , 2015 .

[34]  L. Papadakis,et al.  A computational reduction model for appraising structural effects in selective laser melting manufacturing , 2014 .

[35]  A. Passerone,et al.  THERMOPHYSICAL PROPERTIES OF IN738LC, MM247LC AND CMSX-4 IN THE LIQUID AND HIGH TEMPERATURE SOLID PHASE , 2005 .

[36]  Weeratunge Malalasekera,et al.  An introduction to computational fluid dynamics - the finite volume method , 2007 .

[37]  R. Morgan,et al.  Density analysis of direct metal laser re-melted 316L stainless steel cubic primitives , 2004 .