Polymer-matrix composites carbon fibre characterisation and damage inspection using selectively heating thermography (SeHT) through electromagnetic induction

Abstract Polymer-matrix composites (PMCs) such as glass fibre reinforced polymer (GFRP) and carbon fibre reinforced polymer (CFRP) are being increasingly used in fields of aerospace, renewable energy, civil and architecture. Damages such as broken fibre, impact and delamination are inevitable during either fabrication or lifetime of PMC structures or components. This work proposed selectively heating thermography (SeHT) through electromagnetic induction and infrared temperature measurement for CFRP characterisation and damage inspection. Broken carbon fibres can be easily identified through SeHT whilst inside delamination is difficult to be inspected due to negative influence of temperature gradient, lateral blur effect, and periodic structures. In order to solve this problem, cross correlation (CC) matched filtering algorithm was proposed to enhance the inspection results. Six CFRP laminate samples with impact damages from 2 to 12 J were tested to verify the proposed methods. The experimental studies show that SeHT is capable of characterising fibres and inspecting surface broken area, whilst CC phasegram is capable of inspecting inner delamination due to elimination of non-uniform heating effect and lateral blurring effect. The dependence of damage for CFRP sample on impact energy was also investigated. Through SeHT and CC matched filtering, characterisation and inspection for CFRP can be achieved.

[1]  Manuele Bernabei,et al.  On the evaluation of impact damage on composite materials by comparing different NDI techniques , 2014 .

[2]  Jin-Hwe Kweon,et al.  A study on the failure detection of composite materials using an acoustic emission , 2006 .

[3]  Samir Mustapha,et al.  Assessment of debonding in sandwich CF/EP composite beams using A0 Lamb wave at low frequency , 2011 .

[4]  C. Garnier,et al.  The detection of aeronautical defects in situ on composite structures using Non Destructive Testing , 2011 .

[5]  Wai Lok Woo,et al.  Thermography pattern analysis and separation , 2014 .

[6]  Liang Cheng,et al.  Transient Thermal Behavior of Eddy-Current Pulsed Thermography for Nondestructive Evaluation of Composites , 2013, IEEE Transactions on Instrumentation and Measurement.

[7]  Matthias Goldammer,et al.  INDUCTION AND CONDUCTION THERMOGRAPHY: OPTIMIZING THE ELECTROMAGNETIC EXCITATION TOWARDS APPLICATION , 2009 .

[8]  Yunze He,et al.  Steel Corrosion Characterization Using Pulsed Eddy Current Systems , 2012, IEEE Sensors Journal.

[9]  Alexander Dillenz,et al.  Burst phase-angle thermography with elastic waves , 2002, SPIE Defense + Commercial Sensing.

[10]  Véronique Michaud,et al.  Impact localisation with FBG for a self-healing carbon fibre composite structure , 2011 .

[11]  Yunze He,et al.  Pulsed inductive thermal wave radar (PI-TWR) using cross correlation matched filtering in eddy current thermography , 2015 .

[12]  Yunze He,et al.  Progress and trends in nondestructive testing and evaluation for wind turbine composite blade , 2016 .

[13]  Edouard G Nesvijski,et al.  Some aspects of ultrasonic testing of composites , 2000 .

[14]  G. Tian,et al.  Surface Crack Detection for Carbon Fiber Reinforced Plastic (CFRP) Materials Using Pulsed Eddy Current Thermography , 2011, IEEE Sensors Journal.

[15]  Philippe Hervé,et al.  A comparison between thermosonics and thermography for delamination detection in polymer matrix laminates , 2012 .

[16]  Zhishen Wu,et al.  Modal damping evaluation of hybrid FRP cable with smart dampers for long-span cable-stayed bridges , 2011 .

[17]  K. Reifsnider,et al.  Thermography — An NDI Method for Damage Detection , 1979 .

[18]  K. B. Katnam,et al.  Composite Repair in Wind Turbine Blades: An Overview , 2015 .

[19]  Andreas Nocke,et al.  Review on quality assurance along the CFRP value chain – Non-destructive testing of fabrics, preforms and CFRP by HF radio wave techniques , 2015 .

[20]  David K. Hsu,et al.  An exploration of the utilities of terahertz waves for the NDE of composites , 2011 .

[21]  Gerhard Busse,et al.  Ultrasound Burst Phase Thermography (UBP) for Applications in the Automotive Industry , 2003 .

[22]  Wai Lok Woo,et al.  Automatic Defect Identification of Eddy Current Pulsed Thermography Using Single Channel Blind Source Separation , 2014, IEEE Transactions on Instrumentation and Measurement.

[23]  Yunze He,et al.  Optically and non-optically excited thermography for composites: A review , 2016 .

[24]  Wayne W. Stinchcomb,et al.  Nondestructive evaluation of damage accumulation processes in composite laminates , 1986 .

[25]  Feilu Luo,et al.  Defect characterisation based on heat diffusion using induction thermography testing. , 2012, The Review of scientific instruments.

[26]  Alexander Dillenz,et al.  Ultrasound excited thermography - advances due to frequency modulated elastic waves , 2005 .

[27]  Yunze He,et al.  Non-destructive testing of low-energy impact in CFRP laminates and interior defects in honeycomb sandwich using scanning pulsed eddy current , 2014 .

[28]  Yunze He,et al.  Impact evaluation in carbon fiber reinforced plastic (CFRP) laminates using eddy current pulsed thermography , 2014 .

[29]  Tarun Kant,et al.  Application of polymer composites in civil construction : A general review , 2008 .

[30]  Adriana Savin,et al.  An Electromagnetic Sensor with a Metamaterial Lens for Nondestructive Evaluation of Composite Materials , 2015, Sensors.

[31]  Joung-Man Park,et al.  Nondestructive sensing evaluation of surface modified single-carbon fiber reinforced epoxy composites by electrical resistivity measurement , 2006 .

[32]  G. Giraud,et al.  In-situ monitoring of damage in CFRP laminates by means of AC and DC measurements , 2001 .

[33]  Hoon Sohn,et al.  Visualization of hidden delamination and debonding in composites through noncontact laser ultrasonic scanning , 2014 .

[34]  Feilu Luo,et al.  Defect characterisation using pulsed eddy current thermography under transmission mode and NDT applications , 2012 .

[35]  Yunze He,et al.  Eddy Current Volume Heating Thermography and Phase Analysis for Imaging Characterization of Interface Delamination in CFRP , 2015, IEEE Transactions on Industrial Informatics.

[36]  Yingcheng Hu,et al.  Nondestructive test and prediction of MOE of FRP reinforced fast-growing poplar glulam , 2011 .

[37]  Nasser Qaddoumi,et al.  Defect imaging and characterization in composite structures using near-field microwave nondestructive testing techniques , 2003 .

[38]  Riadh Al-Mahaidi,et al.  Bond defect detection using PTT IRT in concrete structures strengthened with different CFRP systems , 2014 .

[39]  Kenneth Reifsnider,et al.  The Mechanics of Vibrothermography , 1980 .

[40]  R. E. Green,et al.  Thermographic investigation of high-power ultrasonic heating in materials , 1981 .

[41]  Krzysztof Dragan,et al.  Damage identification in aircraft composite structures: A case study using various non-destructive testing techniques , 2015 .

[42]  Wai Lok Woo,et al.  Impact Damage Detection and Identification Using Eddy Current Pulsed Thermography Through Integration of PCA and ICA , 2014, IEEE Sensors Journal.

[43]  Andreas Mandelis,et al.  Thermophotonic radar imaging: An emissivity-normalized modality with advantages over phase lock-in thermography , 2011 .

[44]  Ivan Bartoli,et al.  Damage quantification in polymer composites using a hybrid NDT approach , 2013 .

[45]  Gerhard Busse,et al.  Ultrasound excited thermography using frequency modulated elastic waves , 2003 .

[46]  Yunze He,et al.  Eddy current pulsed phase thermography considering volumetric induction heating for delamination evaluation in carbon fiber reinforced polymers , 2015 .

[47]  Paul L. Rosin,et al.  Neural fuzzy analysis of delaminated composites from shearography imaging , 2001 .

[48]  Wai Lok Woo,et al.  Thermography spatial-transient-stage mathematical tensor construction and material property variation track , 2014 .

[49]  John Montesano,et al.  Use of infrared thermography to investigate the fatigue behavior of a carbon fiber reinforced polymer composite , 2013 .

[50]  G. Busse,et al.  Amplitude-modulated lock-in vibrothermography for NDE of polymers and composites , 1996 .

[51]  Yosuke Nagao,et al.  Damage monitoring of CFRP stiffened panels under compressive load using FBG sensors , 2012 .

[52]  Chun H. Wang,et al.  Improved design methods for scarf repairs to highly strained composite aircraft structure , 2006 .

[53]  Flaw and damage assessment in torsionally loaded CFRP cylinders using experimental and numerical methods , 2015 .