Mixed-mode EMI noise in three-phase DC-fed PWM motor drive system

High density filter design for electromagnetic interference (EMI) noises is essential for the variable speed motor drive system in modern transportation applications. As often being one of the major causes of bulky and heavy filter designs, the mixed-mode (MM) noise phenomenon in the three-phase motor drive system is discussed in this paper. The generation schemes of the MM noises on both DC and AC sides of the system are analyzed. According to the three-phase voltage vector modulation, the MM noises at different switching conditions are compared and summarized. Based on experimental results from a specified prototype system, the existence of the MM noises and its impact on EMI filter design is verified. Investigations show that the implementation of both CM filter and balancing X-capacitors can help attenuate the MM noises effectively.

[1]  Johann W. Kolar,et al.  Guideline for a Simplified Differential-Mode EMI Filter Design , 2010, IEEE Transactions on Industrial Electronics.

[2]  Definition and acquisition of CM and DM EMI noise for general-purpose adjustable speed motor drives , 2004, 2004 IEEE 35th Annual Power Electronics Specialists Conference (IEEE Cat. No.04CH37551).

[3]  Ma Weiming,et al.  A new technique for modeling and analysis of mixed-mode conducted EMI noise , 2004, PESC 2004.

[4]  J.W. Kolar,et al.  Novel three-phase CM/DM conducted emissions separator , 2005, Twentieth Annual IEEE Applied Power Electronics Conference and Exposition, 2005. APEC 2005..

[5]  D. Boroyevich,et al.  Design of output passive EMI filter in DC-fed motor drive , 2012, 2012 Twenty-Seventh Annual IEEE Applied Power Electronics Conference and Exposition (APEC).

[6]  Dan Chen,et al.  Effects of X Capacitors on EMI Filter Effectiveness , 2008, IEEE Transactions on Industrial Electronics.

[7]  H. Akagi,et al.  A passive EMI filter for preventing high-frequency leakage current from flowing through the grounded inverter heat sink of an adjustable-speed motor drive system , 2004, IEEE Transactions on Industry Applications.

[8]  Hirofumi Akagi,et al.  A New Neutral-Point-Clamped PWM Inverter , 1981, IEEE Transactions on Industry Applications.

[9]  Johann W. Kolar,et al.  The Three-Phase Common-Mode Inductor: Modeling and Design Issues , 2011, IEEE Transactions on Industrial Electronics.

[10]  Hung-I Hsieh.  Effects of mix-mode noise emissions on the design method of power factor correction boost rectifier EMI filters , 2010, The 2010 International Power Electronics Conference - ECCE ASIA -.

[11]  Dan Chen,et al.  Mixed-mode EMI noise and its implications to filter design in offline switching power supplies , 2002 .

[12]  Meng Jin,et al.  A new technique for modeling and analysis of mixed-mode conducted EMI noise , 2004, 2004 IEEE 35th Annual Power Electronics Specialists Conference (IEEE Cat. No.04CH37551).

[13]  W. Eberle,et al.  A novel EMI filter design method for switching power supplies , 2004, IEEE Transactions on Power Electronics.

[14]  Hung-I Hsieh,et al.  A filter design procedure incorporating mixed-mode EMI noise for off-line switching power supplies , 2004, The 4th International Power Electronics and Motion Control Conference, 2004. IPEMC 2004..

[15]  Shyama P. Das,et al.  Types of electro magnetic interferences in SMPS and using Y-capacitor for mitigation of Mixed Mode noise , 2010, 2010 International Conference on Power, Control and Embedded Systems.

[16]  H. Akagi,et al.  Attenuation of Conducted EMI Emissions From an Inverter-Driven Motor , 2008, IEEE Transactions on Power Electronics.

[17]  J.W. Kolar,et al.  Impact of EMC Filters on the Power Density of Modern Three-Phase PWM Converters , 2009, IEEE Transactions on Power Electronics.

[18]  K. Satoh,et al.  Damping circuit to suppress motor terminal overvoltage and ringing in PWM inverter-fed AC motor drive systems with long motor leads , 1998, Conference Record of 1998 IEEE Industry Applications Conference. Thirty-Third IAS Annual Meeting (Cat. No.98CH36242).

[19]  Zhang Lei,et al.  Identification of Essential Coupling Path Models for Conducted EMI Prediction in Switching Power Converters , 2004, IEEE Transactions on Power Electronics.

[20]  Kang Jun,et al.  Identification of Essential Coupling Path Models for Conducted EMI Prediction in Switching Power Converters , 2006 .

[21]  Pragasen Pillay,et al.  Modeling, simulation, and analysis of permanent-magnet motor drives. I. The permanent-magnet synchronous motor drive , 1989 .

[22]  F. Wang,et al.  Modeling and design of common-mode inductor for conductive EMI noise suppression in DC-fed motor drive system , 2012, 2012 IEEE Energy Conversion Congress and Exposition (ECCE).

[23]  M. J. Nave,et al.  On modeling the common mode inductor , 1991, IEEE 1991 International Symposium on Electromagnetic Compatibility.