An ergonomic evaluation of a manual metal pouring operation

Abstract Manual material handling is one of the major causes of severe industrial injury. Foundries are an industry where manual material handling is performed routinely. This paper presents a study conducted using a simulated metal pouring operation commonly found in small foundries based on activities. Two laboratory experiments were conducted to evaluate two objectives: (1) to study the effects of different mold heights and carrying distances on physiological responses, and (2) to determine maximum acceptable task frequencies (MAF) for metal pouring. Both objective and subjective measures were used in the study. The objective measures included oxygen uptake, heart rate, and blood pressure while subjective measures included ratings of perceived exertion. Ten healthy males served as participants for these experiments. Results indicated that carrying distance had a significant effect on both heart rate and oxygen consumption. Results also indicated that the participants selected a MAF which was as much as 25% lower than the expectations present at the foundry on which this experiment was modeled. Recommendations for reducing the risk on injury are also discussed in the paper. Relevance to industry Small and medium-sized foundries often have limited resources to deal with occupational safety and health issues. Hence, the results presented in this paper coupled with the engineering and administrative changes, could be used as guidelines for setting good work practices.

[1]  S H Snook,et al.  Psychophysical Studies of Physiological Fatigue Criteria1 , 1969, Human factors.

[2]  M. M. Ayoub,et al.  Development of methodology in biomechanical simulation of manual lifting , 1994 .

[3]  D. Arad,et al.  The incidence and prevalence in nurses of low back pain. A definitive survey exposes the hazards. , 1986, The Australian nurses' journal. Royal Australian Nursing Federation.

[4]  I. Åstrand.  Aerobic work capacity in men and women with special reference to age. , 1960, Acta physiologica Scandinavica. Supplementum.

[5]  S H Snook,et al.  Maximum frequency of lift acceptable to male industrial workers. , 1968, American Industrial Hygiene Association journal.

[6]  S. Snook,et al.  A study of three preventive approaches to low back injury. , 1978, Journal of occupational medicine. : official publication of the Industrial Medical Association.

[7]  S P Dutta,et al.  Developing norms for manual carrying tasks using mechanical efficiency as the optimization criterion. , 1989, Ergonomics.

[8]  S Kumar,et al.  The physiological cost of three different methods of lifting in sagittal and lateral planes. , 1984, Ergonomics.

[9]  S J Legg,et al.  Human capabilities in repetitive lifting. , 1985, Ergonomics.

[10]  Jeffrey E. Fernandez,et al.  Maf for Males Performing Drilling Tasks , 1992 .

[11]  R A Bruce,et al.  Maintenance of aortic pressure and total peripheral resistance during exercise in heat. , 1967, Journal of applied physiology.

[12]  Anil Mital,et al.  Influence of container shape, partitions, frequency, distance, and height level on the maximum acceptable amount of liquid carried by males , 1982 .

[13]  Anil Mital,et al.  Review, Evaluation, and Comparison of Models for Predicting Lifting Capacity , 1980 .

[14]  M Damlund,et al.  Low back strain in Danish semi-skilled construction work. , 1986, Applied ergonomics.

[15]  A Mital,et al.  Psychophysical and physiological responses to lifting symmetrical and asymmetrical loads symmetrically and asymmetrically. , 1986, Ergonomics.

[16]  M M Ayoub,et al.  Psychophysical lifting capacity over extended periods. , 1991, Ergonomics.

[17]  Walton M. Hancock,et al.  Advanced Work Measurement , 1982 .

[18]  P G Dempsey,et al.  Analysis of workers' compensation claims associated with manual materials handling. , 1999, Ergonomics.

[19]  J. Naughton,et al.  Exercise testing and exercise training in coronary heart disease , 1973 .

[20]  M Lortie,et al.  Manual handling in warehouses: the illusion of correct working postures. , 1994, Ergonomics.

[21]  D B Chaffin,et al.  A dynamic biomechanical evaluation of lifting maximum acceptable loads. , 1984, Journal of biomechanics.

[22]  A Mital,et al.  Comprehensive maximum acceptable weight of lift database for regular 8-hour work shifts. , 1984, Ergonomics.

[23]  Stover H. Snook,et al.  The Ergonomics Society The Society's Lecture 1978. THE DESIGN OF MANUAL HANDLING TASKS , 1978 .

[24]  S J Legg,et al.  Metabolic and cardiovascular cost, and perceived effort over an 8 hour day when lifting loads selected by the psychophysical method. , 1985, Ergonomics.

[25]  A. R. Lind,et al.  Comparison of metabolic and ventilatory responses of men to various lifting tasks and bicycle ergometry. , 1978, Journal of applied physiology: respiratory, environmental and exercise physiology.

[26]  A Mital,et al.  Effects of an endurance and strength training programme on lifting capability of males. , 1984, Ergonomics.

[27]  G. Borg.  Perceived exertion as an indicator of somatic stress. , 2019, Scandinavian journal of rehabilitation medicine.

[28]  S H Snook,et al.  The effects of heat stress on manual handling tasks. , 1974, American Industrial Hygiene Association journal.

[29]  Vincent M. Ciriello,et al.  The effects of box size, vertical distance, and height on lowering tasks for female industrial workers , 2005 .

[30]  W Karwowski,et al.  Postural stress analysis in industry. , 1994, Applied ergonomics.

[31]  W. M. Keyserling,et al.  Preemployment strength testing: an updated position. , 1978, Journal of occupational medicine. : official publication of the Industrial Medical Association.

[32]  G B Andersson.  Posture and compressive spine loading: intradiscal pressures, trunk myoelectric activities, intra-abdominal pressures, and biochemical analyses. , 1985, Ergonomics.

[33]  S H Snook,et al.  Maximum weights and work loads acceptable to male industrial workers. A study of lifting, lowering, pushing, pulling, carrying, and walking tasks. , 1970, American Industrial Hygiene Association journal.

[34]  A Garg,et al.  Revised NIOSH equation for the design and evaluation of manual lifting tasks. , 1993, Ergonomics.

[35]  A. Mital.  Maximum weights of lift acceptable to male and female industrial workers for extended work shifts. , 1984, Ergonomics.

[36]  Etienne Grandjean.  Fitting the task to the man , 1969 .

[37]  S. Horvath,et al.  Cardiorespiratory responses during prolonged exercise. , 1961, Journal of applied physiology.

[38]  Rodger J. Koppa,et al.  Maximum acceptable weight of lift for an asymmetrical combination manual handling task , 1989 .

[39]  A Garg,et al.  Effects of lifting frequency and technique on physical fatigue with special reference to psychophysical methodology and metabolic rate. , 1979, American Industrial Hygiene Association journal.

[40]  D. Chaffin.  Manual materials handling and the biomechanical basis for prevention of low-back pain in industry--an overview. , 1987, American Industrial Hygiene Association journal.

[41]  M. Karvonen,et al.  The effects of training on heart rate; a longitudinal study. , 1957, Annales medicinae experimentalis et biologiae Fenniae.