Experimental and numerical investigations of heat transfer characteristics of vertical falling film heat exchanger in data center cabinets

[1]  Ping Song,et al.  A review of energy efficiency evaluation metrics for data centers , 2022, Energy and Buildings.

[2]  Q. Bi,et al.  Experimental investigation of the pressure drop and friction factor of supercritical water in a 2 × 2 rod bundle , 2022, Annals of Nuclear Energy.

[3]  Xiaoqiong Li,et al.  Experimental research on falling film flow and heat transfer characteristics outside the vertical tube , 2021, Applied Thermal Engineering.

[4]  Jiahua Zhu,et al.  Thermophoretic enhancement for fine ash particle capture in a corrugated falling-film channel , 2021 .

[5]  Boqiang Lin,et al.  Towards carbon neutrality by implementing carbon emissions trading scheme: Policy evaluation in China , 2021 .

[6]  Hongbo Tan,et al.  Numerical study on heat and mass transfer characteristics in a randomly packed air cooling tower for large-scale air separation systems , 2021 .

[7]  Derviş Kırıkkaleli,et al.  Revisiting financial development and renewable energy electricity role in attaining China's carbon neutrality target. , 2021, Journal of environmental management.

[8]  T. A. Mouneer,et al.  Effect of data center servers’ power density on the decision of using in-row cooling or perimeter cooling , 2021 .

[9]  Yun-Ze Li,et al.  Numerical Simulation of the Air Cooling System for Scientific Payload Rack on a Space Station , 2020, Energies.

[10]  MCarmen Guerrero Delgado,et al.  Falling-film as natural cooling technique: Modelling and energy impact assessment , 2020 .

[11]  Zhiwen Luo,et al.  Optimization of the thermal environment of a small-scale data center in China , 2020, Energy.

[12]  Jinkyun Cho,et al.  Development and experimental study of an independent row-based cooling system for improving thermal performance of a data center , 2020 .

[13]  Lin Lu,et al.  Fundamentals and applications of CFD technology on analyzing falling film heat and mass exchangers: A comprehensive review , 2020 .

[14]  W. Minkowycz,et al.  Heat transfer and fouling characteristics during falling film evaporation in a vertical sintered tube , 2019 .

[15]  Sihui Hong,et al.  Heat transfer characteristics of obliquely dispensed evaporating falling films on an elliptic tube , 2019, International Journal of Heat and Mass Transfer.

[16]  L. Sheng,et al.  Development of a novel quasi-3D model to investigate the performance of a falling film dehumidifier with CFD technology , 2019, International Journal of Heat and Mass Transfer.

[17]  Pedro S. Moura,et al.  A review on energy efficiency and demand response with focus on small and medium data centers , 2018, Energy Efficiency.

[18]  Xian-he Deng,et al.  Experimental study on heat and mass transfer of falling liquid films in converging-diverging tubes with water , 2018, International Journal of Heat and Mass Transfer.

[19]  G. Longo,et al.  HFC404A condensation inside a small brazed plate heat exchanger: Comparison with the low GWP substitutes propane and propylene , 2017 .

[20]  Chirag R. Kharangate,et al.  Review of computational studies on boiling and condensation , 2017 .

[21]  Zhihang Song.  Numerical cooling performance evaluation of fan-assisted perforations in a raised-floor data center ☆ , 2016 .

[22]  Xiaoze Du,et al.  Effects of continuous and alternant rectangular slots on thermo-flow performances of plain finned tube bundles in in-line and staggered configurations , 2016 .

[23]  Nie Jianping,et al.  PIV and thermal-vision experimental and numerical investigation on the airside performance of slotted fin surfaces , 2015 .

[24]  Alfonso Ortega,et al.  Optimization of Data Center Cooling Efficiency Using Reduced Order Flow Modeling Within a Flow Network Modeling Approach , 2014 .

[25]  Gerard F. Jones,et al.  A review of data center cooling technology, operating conditions and the corresponding low-grade waste heat recovery opportunities , 2014 .

[26]  V. Armenio,et al.  Numerical model for thin liquid film with evaporation and condensation on solid surfaces in systems with conjugated heat transfer , 2013 .

[27]  Saman K. Halgamuge,et al.  Potential of air-side economizers for data center cooling: A case study for key Australian cities , 2013 .

[28]  Masud Behnia,et al.  Cooling solutions in an operational data centre: A case study , 2011 .

[29]  Masoud Rahimi,et al.  CFD modeling of flow and heat transfer in a thermosyphon , 2010 .

[30]  Geraldine J. Heynderickx,et al.  Modeling the evaporation of a hydrocarbon feedstock in the convection section of a steam cracker , 2009, Comput. Chem. Eng..

[31]  Jer‐Huan Jang,et al.  Thermal protection with liquid film in turbulent mixed convection channel flows , 2006 .

[32]  M. Feddaoui,et al.  The numerical computation of the evaporative cooling of falling water film in turbulent mixed convection inside a vertical tube , 2006 .

[33]  S. Paras,et al.  Characteristics of developing free falling films at intermediate Reynolds and high Kapitza numbers , 2004 .

[34]  Jung-Yang San,et al.  Second-law analysis of a wet crossflow heat exchanger , 2000 .

[35]  Wei‐Mon Yan.  Evaporative cooling of liquid film in turbulent mixed convection channel flows , 1998 .

[36]  W. Yan,et al.  Mixed convection heat and mass transfer in a vertical channel with film evaporation , 1993 .

[37]  Y. Tsay,et al.  Evaporative cooling of liquid film through interfacial heat and mass transfer in a vertical channel. I, Experimental study , 1991 .

[38]  Robert J. Moffat,et al.  Describing the Uncertainties in Experimental Results , 1988 .

[39]  K. Gardner.  Mean Temperature Difference in Multipass Exchangers , 1941 .

[40]  W. Prüger.  Die Verdampfungsgeschwindigkeit der Flüssigkeiten , 1940 .

[41]  M. Knudsen,et al.  Die maximale Verdampfungsgeschwindigkeit des Quecksilbers , 1915 .