Acoustic emission analysis of Vickers indentation fracture of cermet and ceramic coatings

The aim of this work was to develop an instrumented experimental methodology of quantitative material evaluation based on the acoustic emission (AE) monitoring of a dead-weight Vickers indentation. This was to assess the degree of cracking and hence the toughness of thermally sprayed coatings. AE data were acquired during indentation tests on samples of coatings of nominal thickness 250–325 µm at a variety of indentation loads ranging from 49 to 490 N. Measurements were carried out on five different carbide and ceramic coatings (HVOF as-sprayed WC-12%Co (JP5000 and JetKote), HIPed WC-12%Co (JetKote) and as-sprayed Al2O3 (APS/Metco and HVOF/theta-gun)). The raw AE signals recorded during indentation were analysed and the total surface crack length around the indent determined. The results showed that the total surface crack length measured gave fracture toughness (K1c) values which were consistent with the published literature for similar coatings but evaluated using the classical approach (Palmqvist/half-penny model). Hence, the total surface crack length criteria can be applied to ceramic and cermet coatings which may or may not exhibit fracture via radial cracks. The values of K1c measured were 3.4 ± 0.1 MPa m1/2 for high-velocity oxygen fuel (HVOF) (theta-gun) Al2O3, 4.6 ± 0.3 MPa m1/2 for as-sprayed HVOF (JetKote) WC-12%Co, 7.1±0.1 MPa m1/2 for as-sprayed HVOF (JP5000) WC-12%Co and 7.4 ± 0.2 MPa m1/2 for HIPed HVOF (JetKote) WC-12%Co coatings. The crack lengths were then calibrated against the AE response and correlation coefficients evaluated. The values of K1c measured using AE correlations were 3.3 MPa m1/2 for HVOF (theta-gun) Al2O3, 2.6 MPa m1/2 for APS (Metco) Al2O3, 2.5 MPa m1/2 for as-sprayed HVOF (JetKote) WC-12%Co, 6.3 MPa m1/2 for as-sprayed HVOF (JP5000) WC-12%Co and 8.6 MPa m1/2 for HIPed HVOF (JetKote) WC-12%Co coatings. It is concluded that within each category of coating type, AE can be used as a suitable surrogate for crack length measurement for assessing coating quality. Hence, a full measure of crack prevalence which would require time-consuming fractal dimension analysis can be made redundant for a given coating type, offering a motivation for AE-based indentation testing as a measure of quality control. Similarly, for cases where surface crack length cannot be measured due to delamination/spallation of surface, AE-based fracture toughness provides a benchmark for coating quality assessment.

[1]  E. Fuller,et al.  Equilibrium penny-like cracks in indentation fracture , 1975 .

[2]  G. Fantozzi,et al.  Evaluation by indentation of fracture toughness of ceramic materials , 1990 .

[3]  A. Celli,et al.  Fractal analysis of cracks in alumina–zirconia composites , 2003 .

[4]  M. Yao,et al.  Cracking analysis of HVOF coatings under Vickers indentation , 2008 .

[5]  Robert Lewis Reuben,et al.  Indentation testing and its acoustic emission response: applications and emerging trends , 2011 .

[6]  R. Krishnamurthy,et al.  Microwave glazing of alumina–titania ceramic composite coatings , 2001 .

[7]  Sunghak Lee,et al.  Acoustic emission during indentation fracture of soda-lime glass , 1984 .

[8]  B. Mellor,et al.  Fracture toughness and crack morphologies in eroded WC-Co-Cr thermally sprayed coatings , 1998 .

[9]  Pornchai Nivesrangsan,et al.  Multi-source, multi-sensor approaches to diesel engine monitoring using acoustic emission , 2004 .

[10]  T. Itsukaichi,et al.  Sliding Wear Evaluation of Hot Isostatically Pressed (HIPed) Thermal Spray Cermet Coatings , 2003, Thermal Spray 2003: Proceedings from the International Thermal Spray Conference.

[11]  Acoustic Emission Analysis of Nanoindentation-Induced Fracture Events , 2006 .

[12]  C. Scruby,et al.  An introduction to acoustic emission , 1986 .

[13]  L. Edwards,et al.  Neutron diffraction residual strain measurements in post-treated thermal spray cermet coatings , 2008 .

[14]  D. Bhattacharya,et al.  Studies on indentation fracture toughness on ceramic and ceramic composite using acoustic emission technique , 1999 .

[15]  L. Edwards,et al.  Residual Strain Measurements in Thermal Spray Cermet Coatings via Neutron Diffraction , 2006 .

[16]  L. Shaw,et al.  Indentation fracture behavior of plasma-sprayed nanostructured Al2O3-13wt.%TiO2 coatings , 2003 .

[17]  Manabu Tanaka,et al.  Fracture toughness and crack morphology in indentation fracture of brittle materials , 1996, Journal of Materials Science.

[18]  C. Baudín,et al.  Fractographic and acoustic emission of mullite-alumina-zirconia composites prepared by reaction sintering , 1987 .

[19]  P. J. Modenesi,et al.  Toughness evaluation of HVOF WC–Co coatings using non-linear regression analysis , 2003 .

[20]  John Alexander Steel,et al.  The Use of Acoustic Emission to Characterize Fracture Behavior During Vickers Indentation of HVOF Thermally Sprayed WC-Co Coatings , 2009 .

[21]  R. Bradt,et al.  On the Vickers Indentation Fracture Toughness Test , 2007 .

[22]  A. A. Griffith.  The Phenomena of Rupture and Flow in Solids , 1921 .

[23]  Robert Lewis Reuben,et al.  An improved measurement of Vickers indentation behaviour through enhanced instrumentation , 2011 .

[24]  Steve Bull,et al.  Nanoindentation of coatings , 2005 .

[25]  B. Lawn,et al.  Indentation fracture: principles and applications , 1975 .

[26]  K. Niihara,et al.  A fracture mechanics analysis of indentation-induced Palmqvist crack in ceramics , 1983 .

[27]  R. Reuben,et al.  Neutron diffraction residual strain measurements in alumina coatings deposited via APS and HVOF techniques , 2010 .

[28]  J. Li,et al.  Polishing-induced pull outs of plasma sprayed Cr3C2-NiCr coating , 1999 .

[29]  C. Ponton,et al.  Vickers indentation fracture toughness test Part 1 Review of literature and formulation of standardised indentation toughness equations , 1989 .

[30]  Dehua Yang,et al.  Indentation fracture toughness and acoustic energy release in tetrahedral amorphous carbon diamond-like thin films , 2006 .

[31]  M. Fitzpatrick,et al.  Residual Strain and Fracture Response of Al2O3 Coatings Deposited via APS and HVOF Techniques , 2011, Journal of Thermal Spray Technology.

[32]  Yoshio Saito,et al.  Acoustic Emission and Deformation Mode in Ceramics During Indentation , 1994 .

[33]  G. Sundararajan,et al.  Processing–structure–property correlation and decarburization phenomenon in detonation sprayed WC–12Co coatings , 2008 .

[34]  I. Wright,et al.  Indentation fracture of WC-Co cermets , 1985 .

[35]  P. Scardi,et al.  Residual stresses in HVOF-sprayed ceramic coatings , 2008 .

[36]  Xi Chen,et al.  On the determination of residual stress and mechanical properties by indentation , 2006 .

[37]  John R. Rice,et al.  Fracture of Brittle Solids (Cambridge Solid State Science Series) , 1975 .

[38]  I. Roman,et al.  Microhardness as a simple means of estimating relative wear resistance of carbide thermal spray coatings: Part 1. characterization of cemented carbide coatings , 2002 .

[39]  Ansar Ahmad,et al.  Fracture properties of sintered UO2 ceramic pellets with duplex microstructure , 2007 .

[40]  D. Hasselman,et al.  Evaluation ofKIc of brittle solids by the indentation method with low crack-to-indent ratios , 1982 .

[41]  N. Faisal.  Acoustic emission analysis for quality assessment of thermally sprayed coatings , 2009 .