Structural member stability verification in the new Part 1‐1 of the second generation of Eurocode 3

This two-part article gives an overview of the developments of the structural member verification in prEN 1993-1-1:2020 “Eurocode 3: Design of steel structures – part 1-1: General rules and rules for buildings”, one of the second generation of Eurocodes. These developments were undertaken by Working Group 1 (WG1) of Subcommittee CEN/TC250/SC3 and by Project Team 1 (SC3.PT1) responsible for drafting the new version of EN 1993- 1-1. In the past, WG1 collected many topics needing improvement, and the systematic review conducted every five years also yielded topics needing further development. Based on this, the current version of EN 1993-1-1 has been developed into a new draft version prEN 1993-1-1:2020 enhancing “ease of use”. The technical content of this new draft was laid down at the end of 2019. Many improvements to design rules have been established with respect to structural analysis, resistance of cross-sections and stability of members. This two-part article focuses on member stability design rules and deals with the basis for the calibration of partial factors, the introduction of more economic design rules for semi-compact sections, methods for structural analysis in relation to the appropriate member stability design rules, new design rules for lateral torsional buckling plus other developments and innovations. This second part of the article is dedicated to illustrating the most relevant changes to member buckling design rules.

[1]  Markus Knobloch,et al.  Assessment of the plastic capacity of I-shaped cross-sections according to the partial internal forces method , 2019, Engineering Structures.

[2]  Markus Knobloch,et al.  The simplified method of the equivalent compression flange , 2019, Steel Construction.

[3]  D. A. Nethercot,et al.  Designer's guide to EN 1993-1-1 : Eurocode 3: Design of Steel Structures : General Rules and Rules for Buildings /L. Gardner and D. A. Nethercot , 2005 .

[4]  Markus Knobloch,et al.  Structural member stability verification in the new Part 1‐1 of the second generation of Eurocode 3 , 2020, Steel Construction.

[5]  David A. Nethercot,et al.  An analysis of the true bending strength of steel beams , 1998 .

[6]  Alain Bureau,et al.  Simplified method for lateral‐torsional buckling of beams with lateral restraints , 2019, Steel Construction.

[7]  H. H. Snijder,et al.  Experimental investigation on residual stresses in heavy wide flange QST steel sections , 2013 .

[8]  Torsten Glitsch Dipl.-Ing. Vereinfachter Nachweis für I- und U-Träger – beansprucht durch doppelte Biegung und Torsion , 2004 .

[9]  Anna‐Lena Bours,et al.  Ergänzende Untersuchungen zum Tragverhalten einfachsymmetrischer I‐Querschnitte unter Biegung, Druck und Torsion , 2019, Stahlbau.

[10]  Joachim Lindner,et al.  Vereinfachter Nachweis für I‐ und U‐Träger – beansprucht durch doppelte Biegung und Torsion , 2004 .

[11]  Tak-Ming Chan,et al.  Cross-section classification of elliptical hollow sections , 2007 .

[12]  Harald Unterweger,et al.  Steifenlose Krafteinleitung bei Biegeträgern , 2015 .

[13]  Nicoleta Popa,et al.  Buckling curves for heavy wide flange QST columns based on statistical evaluation , 2014 .

[14]  Rebekka Winkler,et al.  Zum Stabilitätsnachweis von Stahlbauteilen aus einfach‐ und doppeltsymmetrischen I‐Querschnitten unter Biegung, Druck und Torsion , 2018 .

[15]  C. R. Hendy,et al.  Designers' Guide to EN 1993-2 Eurocode 3: Design of Steel Structures, Part 2: Steel Bridges , 2007 .