Point load actuation on plate structures based on triangular piezoelectric patches

This paper investigates the design of a perfect point load actuator based on flat triangular piezoelectric patches. Applying a difference of electric potential between the electrodes of a triangular patch leads to point loads at the tips and distributed moments along the edges of the electrodes. The previously derived analytical expressions of these forces show that they depend on two factors: the width over height (b/l) ratio of the triangle, and the ratio of the in-plane piezoelectric properties (e31/e32) of the active layer of the piezoelectric patch. In this paper, it is shown that by a proper choice of b/l and of the piezoelectric properties, the moments can be cancelled, so that if one side of the triangle is clamped, a perfect point load actuation can be achieved. This requires e31/e32 to be negative, which imposes the use of interdigitated electrodes instead of continuous ones. The design of two transducers with interdigitated electrodes for perfect point load actuation on a clamped plate is verified with finite element calculations. The first design is based on a full piezoelectric ceramic patch and shows superior actuation performance than the second design based on a piezocomposite patch with a volume fraction of fibres of 86%. The results show that both designs lead to perfect point load actuation while the use of an isotropic PZT patch with continuous electrodes gives significantly different results.Copyright © 2014 Techno-Press, Ltd.

[1]  M. Friswell,et al.  Sensor shape design for piezoelectric cantilever beams to harvest vibration energy , 2010 .

[2]  S. E. Burke,et al.  Active vibration control of a simply supported beam using a spatially distributed actuator , 1987, IEEE Control Systems Magazine.

[3]  J. M. Sullivan,et al.  DISTRIBUTED SENSOR/ACTUATOR DESIGN FOR PLATES: SPATIAL SHAPE AND SHADING AS DESIGN PARAMETERS , 1997 .

[4]  C. K. Lee.  Theory of laminated piezoelectric plates for the design of distributed sensors/actuators. Part I: Governing equations and reciprocal relationships , 1990 .

[5]  C. K. Lee,et al.  Piezoelectric modal sensor/actuator pairs for critical active damping vibration control , 1991 .

[6]  Paolo Gardonio,et al.  Smart panels with velocity feedback control systems using triangularly shaped strain actuators. , 2005, The Journal of the Acoustical Society of America.

[7]  Michael I. Friswell,et al.  Structural health monitoring using shaped sensors , 2009 .

[8]  Leslie E. Cross,et al.  Composite Piezoelectric Transducers , 1980 .

[9]  D. Briand,et al.  Finite element analysis and experiments on a silicon membrane actuated by an epitaxial PZT thin film for localized-mass sensing applications , 2011 .

[10]  A. Preumont,et al.  The damping of a truss structure with a piezoelectric transducer , 2008 .

[11]  Francis C. Moon,et al.  Modal Sensors/Actuators , 1990 .

[12]  Shawn E. Burke,et al.  Modeling approach for two‐dimensional distributed transducers of arbitrary spatial distribution , 1996 .

[13]  Stephen J. Elliott,et al.  Active Vibration Damping Using an Inertial, Electrodynamic Actuator (DETC2005-84632) , 2007 .

[14]  Hoon Sohn,et al.  Overview of Piezoelectric Impedance-Based Health Monitoring and Path Forward , 2003 .

[15]  A. Preumont,et al.  Mixing Rules for the Piezoelectric Properties of Macro Fiber Composites , 2009 .

[16]  Glaucio H. Paulino,et al.  Multi‐actuated functionally graded piezoelectric micro‐tools design: A multiphysics topology optimization approach , 2009 .

[17]  A. Deraemaeker,et al.  Equivalent loads for two-dimensional distributed anisotropic piezoelectric transducers with arbitrary shapes attached to thin plate structures. , 2011, The Journal of the Acoustical Society of America.