Design and fabrication of SAW pressure, temperature and impedance sensors using novel multiphysics simulation models

Abstract Surface acoustic wave (SAW) devices have been shown to be suitable for many applications. Some of these applications are temperature, pressure and impedance-based sensors. In this study, we investigate the performance of a SAW resonator as temperature and pressure sensors, and a reflective differential delay line (RDDL) structure as an impedance sensor. The SAW sensors were designed using a proposed FEM-based multiphysics model on COMSOL® and fabricated using photolitography over a 128° YX LiNbO3 substrate for an operation frequency of 65 MHz. Using a vector network analyzer (VNA), the devices were characterized; frequency shifts on the S11 parameter of resonators were observed depending on the applied external pressure and temperature changes, and amplitude variations for impedance changes in the case of RDDL. The experimental results were compared with simulation data. The evaluated sensitivities were 87.81 ppm/°C, 0.9 ppm/kPa and 0.0023 dB/Ω.

[1]  Inwhee Park,et al.  Long range wireless characterisation of 2.4 GHz SAW-based pressure sensor using network analyser , 2006 .

[2]  Wen Wang,et al.  Optimal design on SAW sensor for wireless pressure measurement based on reflective delay line , 2007 .

[3]  H. Huet,et al.  P1I-5 Micro-Machined, All Quartz Package, Passive Wireless SAW Pressure and Temperature Sensor , 2006, 2006 IEEE Ultrasonics Symposium.

[4]  Tao Han,et al.  SAW-RFID enabled temperature sensor , 2013 .

[5]  S. Ballandras,et al.  Theoretical and experimental analysis of high Q SAW resonator transient response in a wireless sensor interrogation application , 2012, 2012 IEEE International Frequency Control Symposium Proceedings.

[6]  F. Seifert,et al.  Quartz pressure sensor based on SAW reflective delay line , 1996, 1996 IEEE Ultrasonics Symposium. Proceedings.

[7]  Haekwan Oh,et al.  Development of a high-sensitivity strain measurement system based on a SH SAW sensor , 2012 .

[8]  Yu.N. Vlassov,et al.  Precision SAW pressure sensors , 1993, 1993 IEEE International Frequency Control Symposium.

[9]  Bo Liang,et al.  Comparative study of SAW temperature sensor based on different piezoelectric materials and crystal cuts for passive wireless measurement , 2010, 2010 IEEE Sensors.

[10]  Gang Xu,et al.  Pressure and Temperature Microsensor Based on Surface Acoustic Wave in TPMS , 2010 .

[11]  A KoellenspergerP,et al.  王水による化学ウェットエッチングによる白金(Pt)薄膜のパターン形成 , 2012 .

[12]  P. Marć,et al.  Application of Equivalent-Network Model to Analysis and Synthesis of the Saw Resonator , 2001 .

[13]  W. Buff,et al.  Passive remote sensing for temperature and pressure using SAW resonator devices , 1998, IEEE Transactions on Ultrasonics, Ferroelectrics and Frequency Control.

[14]  Lilia Arapan.  Thin Film Plate Acoustic Resonators for Frequency Control and Sensing Applications , 2012 .

[15]  Dan Xiang,et al.  Wireless surface acoustic wave radio frequency identification (SAW-RFID) sensor system for temperature and strain measurements , 2011, 2011 IEEE International Ultrasonics Symposium.

[16]  Wen Wang,et al.  A novel 440 MHz wireless SAW microsensor integrated with pressure–temperature sensors and ID tag , 2007 .

[17]  Nasser N Peyghambarian,et al.  CMOS switched capacitor liquid crystal driver , 2006 .

[18]  W. Buff,et al.  High-temperature 434 MHz surface acoustic wave devices based on GaPO/sub 4/ , 2006, IEEE Transactions on Ultrasonics, Ferroelectrics and Frequency Control.

[19]  Fengqi Yu,et al.  A Novel FEA Simulation Model for RFID SAW Tag , 2009, IEEE Transactions on Ultrasonics, Ferroelectrics and Frequency Control.

[20]  G. Scholl,et al.  Theory and application of passive SAW radio transponders as sensors , 1998, IEEE Transactions on Ultrasonics, Ferroelectrics and Frequency Control.