Detection of fatigue cracks and torque loss in bolted joints

Fatigue crack growth during the service life of aging aircraft is a critical issue and monitoring of such cracks in structural hotspots is the goal of this research. This paper presents a procedure for classification and detection of cracks generated in bolted joints which are used at numerous locations in aircraft structures. Single lap bolted joints were equipped with surface mounted piezoelectric (pzt) sensors and actuators and were subjected to cyclic loading. Crack length measurements and sensor data were collected at different number of cycles and with different torque levels. A classification algorithm based on Support Vector Machines (SVMs) was used to compare signals from a healthy and damaged joint to classify fatigue damage at the bolts. The algorithm was also used to classify the amount of torque in the bolt of interest and determine if the level of torque affected the quantification and localization of the crack emanating from the bolt hole. The results show that it is easier to detect the completely loose bolt but certain changes in torque, combined with damage, can produce some non-unique classifier solutions.

[1]  J. M. Alegre,et al.  EFFECT OF CLAMPING FORCE ON THE FATIGUE BEHAVIOUR OF PUNCHED PLATES SUBJECTED TO AXIAL LOADING , 2006 .

[2]  L Padula Sharon,et al.  Optimization Strategies for Sensor and Actuator Placement , 1999 .

[3]  Antonia Papandreou-Suppappola,et al.  On the use of the matching pursuit decomposition signal processing technique for structural health monitoring , 2005, SPIE Smart Structures and Materials + Nondestructive Evaluation and Health Monitoring.

[4]  D. R. Harting,et al.  Demodulated resonance analysis - A powerful incipient failure detection technique , 1978 .

[5]  Har Prashad,et al.  Diagnostic monitoring of rolling-element bearings by high-frequency resonance technique© , 1985 .

[6]  Jeffrey Vogwell,et al.  Effect of torque tightening on the fatigue strength of bolted joints , 2006 .

[7]  B. Datner,et al.  Analysis of Roller/Ball Bearing Vibrations , 1979 .

[8]  Xu Zhou,et al.  Wave scattering analysis of bolted joints , 2006, SPIE Smart Structures and Materials + Nondestructive Evaluation and Health Monitoring.

[9]  Bo-Suk Yang,et al.  Application of nonlinear feature extraction and support vector machines for fault diagnosis of induction motors , 2007, Expert Syst. Appl..

[10]  R. M. Stewart,et al.  Detection of Rolling Element Bearing Damage by Statistical Vibration Analysis , 1978 .

[11]  Shih-Fu Ling,et al.  Bearing failure detection using matching pursuit , 2002 .

[12]  Steven E. Olson,et al.  Fastener Damage Estimation in a Square Aluminum Plate , 2006 .

[13]  Jun Ma,et al.  Wavelet decomposition of vibrations for detection of bearing-localized defects , 1997 .

[14]  Peter Brett,et al.  An approach to optimise the critical sensor locations in one-dimensional novel distributive tactile surface to maximise performance , 2003 .

[15]  E. Moulin,et al.  Health monitoring of a composite wingbox structure. , 2004, Ultrasonics.

[16]  Paolo Lazzarin,et al.  Scatter bands summarizing the fatigue strength of aluminium alloy bolted joints , 1997 .

[17]  Xu Zhou,et al.  Acoustic Based Structural Health Monitoring for Composites Using Optimal Sensor Placement: Analysis and Experiments , 2009 .

[18]  Anindya Ghoshal,et al.  Wave propagation sensing for damage detection in plates , 2002, SPIE Smart Structures and Materials + Nondestructive Evaluation and Health Monitoring.

[19]  Anindya Ghoshal,et al.  Damage localisation in composite and metallic structures using a structural neural system and simulated acoustic emissions , 2007 .

[20]  Stéphane Mallat,et al.  Matching pursuits with time-frequency dictionaries , 1993, IEEE Trans. Signal Process..

[21]  P. D. McFadden,et al.  Vibration monitoring of rolling element bearings by the high-frequency resonance technique — a review , 1984 .

[22]  A.N. Srivastava,et al.  Classification of Damage Signatures in Composite Plates using One-Class SVMs , 2007, 2007 IEEE Aerospace Conference.

[23]  Chung Bang Yun,et al.  Damage diagnostics on a welded zone of a steel truss member using an active sensing network system , 2007 .

[24]  Fabio Matta,et al.  Acoustic Emission Damage Assessment of Steel/CFRP Bonds for Rehabilitation , 2006 .