Accurate measurements of plate thickness with variable lift-off using a combined inductive and capacitive sensor

Abstract In eddy current testing, lift-off variations between sensor and sample plate affect sensor inductance and consequently inferred thickness. In this paper, a novel combined inductive and capacitive sensor is designed in which the output of the capacitive sensor can be used to infer the lift-off. An algorithm is proposed to combine the inferred lift-off and the inductance measurement for predicting thickness. The effect of lift-off variations is significantly reduced using this combined sensor approach. Compared to the multi-frequency thickness measurements in our previous work, this only requires a single frequency measurement for each of the capacitive and inductive modalities, leading to a relaxation of the instrument and measurement requirements.

[1]  Philip J. Withers,et al.  Noncontact Characterization of Carbon-Fiber-Reinforced Plastics Using Multifrequency Eddy Current Sensors , 2009, IEEE Transactions on Instrumentation and Measurement.

[2]  Wuliang Yin,et al.  Simultaneous measurement of distance and thickness of a thin metal plate with an electromagnetic sensor using a simplified model , 2003, IEEE Transactions on Instrumentation and Measurement.

[4]  Boby George,et al.  A Combined Inductive–Capacitive Proximity Sensor for Seat Occupancy Detection , 2010, IEEE Transactions on Instrumentation and Measurement.

[5]  Erol Uzal,et al.  Thickness and conductivity of metallic layers from eddy current measurements , 1992 .

[6]  Wuliang Yin,et al.  A Novel Dual Modality Sensor With Sensitivities to Permittivity, Conductivity, and Permeability , 2019, IEEE Sensors Journal.

[7]  Wuliang Yin,et al.  Thickness measurement of non-magnetic plates using multi-frequency eddy current sensors , 2007 .

[8]  Wuliang Yin,et al.  Reducing the Lift-Off Effect on Permeability Measurement for Magnetic Plates From Multifrequency Induction Data , 2018, IEEE Transactions on Instrumentation and Measurement.

[9]  C. Dodd,et al.  ANALYTICAL SOLUTIONS TO EDDY--CURRENT PROBE COIL PROBLEMS. , 1968 .

[10]  Boby George,et al.  An Eddy Current-Capacitive Crack Detection Probe with High Insensitivity to Lift-Off , 2018, IECON 2018 - 44th Annual Conference of the IEEE Industrial Electronics Society.

[11]  Kai Xu,et al.  A Novel Triple-Coil Electromagnetic Sensor for Thickness Measurement Immune to Lift-Off Variations , 2016, IEEE Transactions on Instrumentation and Measurement.

[12]  Wuliang Yin,et al.  A Novel Compensation Algorithm for Thickness Measurement Immune to Lift-Off Variations Using Eddy Current Method , 2016, IEEE Transactions on Instrumentation and Measurement.

[13]  Wuliang Yin,et al.  A multi-frequency NDT system for imaging and detection of cracks , 2018, 2018 IEEE International Symposium on Circuits and Systems (ISCAS).

[14]  Dominique Placko,et al.  Wall thickness evaluation of single-crystal hollow blades by eddy current sensor , 2001 .

[15]  Boby George,et al.  Advances in Capacitive, Eddy Current, and Magnetic Displacement Sensors and Corresponding Interfaces , 2017, IEEE Transactions on Industrial Electronics.

[16]  M. Maeda,et al.  A New Eddy Current Surface Probe for Short Flaws with Minimal Lift‐Off Noise , 2003 .

[17]  Ermanno Pinotti,et al.  Simple Lock-In Technique for Thickness Measurement of Metallic Plates , 2014, IEEE Transactions on Instrumentation and Measurement.

[18]  Luigi Ferrigno,et al.  Evaluation of the lift-off robustness of eddy current imaging techniques , 2017 .

[19]  Wuliang Yin,et al.  Imaging x70 weld cross-section using electromagnetic testing , 2018, NDT & E International.

[20]  Zhihua Feng,et al.  Non-contact online thickness measurement system for metal films based on eddy current sensing with distance tracking technique. , 2016, The Review of scientific instruments.

[21]  Y. Le Bihan,et al.  Lift-off and tilt effects on eddy current sensor measurements: a 3-D finite element study , 2002 .

[22]  Gui Yun Tian,et al.  Reduction of lift-off effects for pulsed eddy current NDT , 2005 .

[23]  Wuliang Yin,et al.  Thickness Measurement of Metallic Plates With an Electromagnetic Sensor Using Phase Signature Analysis , 2008, IEEE Transactions on Instrumentation and Measurement.