A Review on Model and Control of Electromagnetic Active Engine Mounts

The isolation of the body from engine vibration is the most challenging and disruptive vibrational problem. Active engine mounts (AEMs), especially electromagnetic AEMs, achieve a significant performance improvement in decreasing the wide frequency band vibration. Increasing research interest is necessary to provide the academic community with a guideline for electromagnetic AEMs. Therefore, the current review aims to comprehensively supplement the review of AEMs. The key reviews of electromagnetic AEMs focus on (1) general considerations of electromagnetic AEMs, (2) models, and (3) control strategies. This paper presents a review of the current status and developmental progress of AEMs. A theoretical model, a finite-element model, and the identification (or experimental modelling) of electromagnetic AEMs during the last 2 decades are then studied. Finally, control strategies, such as classical control, adaptive control, and two degree of freedom (2DOF) control, are discussed and compared. The main purpose of this paper is to meet the needs of researchers and engineers engaged in electromagnetic AEM analysis and control.

[1]  Akira Takahashi,et al.  NV Countermeasure Technology for a Cylinder-On-Demand Engine- Development of Active Booming Noise Control System Applying Adaptive Notch Filter , 2004 .

[2]  Heidar Ali Talebi,et al.  A robust adaptive control scheme for an active mount using a dynamic engine model , 2015 .

[3]  Bo-Ha Lee,et al.  Design of an active control engine mount using a direct drive electrodynamic actuator , 2007 .

[4]  Katsuhiro Hirata,et al.  Proposal of linear oscillatory actuator using DC motor for active control engine mount , 2016 .

[5]  Daniel L. Palumbo,et al.  Recent advances in active noise and vibration control at NASA Langley Research Center , 2002 .

[6]  Katsuhiro Hirata,et al.  Linear oscillatory actuator using new magnetic movement converter , 2013, 2013 IEEE International Conference on Mechatronics and Automation.

[7]  Stephen J. Elliott,et al.  A multiple error LMS algorithm and its application to the active control of sound and vibration , 1987, IEEE Trans. Acoust. Speech Signal Process..

[8]  Jae-Cheon Lee,et al.  Correlation Analysis of TPA Output Variables in a Pneumatic Active Engine Mount System , 2012 .

[9]  Takao Ushijima,et al.  Active Engine Mount with Piezo-Actuator for Vibration Control , 1993 .

[10]  Vahid Fakhari,et al.  Vibration control of an automotive engine using active mounts , 2013 .

[12]  Siamak Arzanpour,et al.  Design of a solenoid valve based active engine mount , 2012 .

[13]  Shi Wen-ku.  A Study of the Isolation Characteristics of a Active Control Hydraulic Mount with Electromagnetic-Actuator , 2006 .

[14]  Kosuke Sakamoto,et al.  Development of Simulation Model for Active Control Engine Mount , 2006 .

[15]  S. C. Southward,et al.  Active Control of Noise and Vibration , 1996 .

[16]  Andrew Hillis.  Multi-input multi-output control of an automotive active engine mounting system , 2011 .

[17]  Marcelo J. Dapino,et al.  Design and modeling of a hydraulically amplified magnetostrictive actuator for automotive engine mounts , 2010, Smart Structures and Materials + Nondestructive Evaluation and Health Monitoring.

[18]  M. F. Golnaraghi,et al.  Development of a bushing with an active compliance chamber for variable displacement engines , 2008 .

[19]  Katsuhiro Hirata,et al.  A Study on Electromagnetic Actuator with Two-Degree-of-Freedom , 2005 .

[20]  Rini Akmeliawati,et al.  Terminal sliding mode control for active engine mounting system , 2009, 2009 IEEE/ASME International Conference on Advanced Intelligent Mechatronics.

[21]  Christian Bohn,et al.  An Overview of Recent Automotive Applications of Active Vibration Control , 2004 .

[22]  M. F. Golnaraghi,et al.  Active decoupler hydraulic engine mount design with application to variable displacement engine , 2011 .

[23]  Arthur P. Berkhoff,et al.  A technique for improved stability of adaptive feedforward controllers without detailed uncertainty measurements , 2011 .

[24]  Sen M. Kuo,et al.  Active noise control: a tutorial review , 1999, Proc. IEEE.

[25]  J. Shynk.  Frequency-domain and multirate adaptive filtering , 1992, IEEE Signal Processing Magazine.

[26]  Waleed Fekry Faris,et al.  Active Engine Mounting Control Algorithm Using Neural Network , 2009 .

[27]  Masayoshi Tomizuka,et al.  Smooth robust adaptive sliding mode control of manipulators with guaranteed transient performance , 1994, Proceedings of 1994 American Control Conference - ACC '94.

[28]  김정훈,et al.  Development of Feed forward Control Algorithm for Active Pneumatic Engine Mount System , 2008 .

[29]  Masao Nagai,et al.  A Study on Active Hydraulic Engine Mount to Reduce Interior Car Noise and Vibration over Wide Frequency Band , 2011 .

[30]  A. R. Payne.  The Dynamic Properties of Carbon Black-Loaded Natural Rubber Vulcanizates. Part I , 1962 .

[31]  Futoshi Kobayashi,et al.  The 17th International Symposium on Applied Electromagnetics and Mechanics (ISEM2015) , 2016 .

[32]  Waleed Fekry Faris,et al.  Active engine mounting controller design using linear quadratic regulator and proportional integral derivative , 2011, Int. J. Autom. Control..

[33]  Kwang-Keun Shin.  Active Vibration Control of Active Fuel Management Engines Using Active Engine Mounts , 2007 .

[34]  Stephen J. Elliott,et al.  Signal Processing for Active Control , 2000 .

[35]  Markus Rupp,et al.  Combination of map-based and adaptive feedforward control algorithms for active engine mounts , 2017 .

[36]  David P Stoten,et al.  A comparison of two adaptive algorithms for the control of active engine mounts , 2005 .

[37]  Seung-Bok Choi,et al.  A robust vibration control for a multi-active mount system subjected to broadband excitation , 2011 .

[38]  Shi Wen-ku.  Simulation Analysis of Vibration Isolation for Engine Piezoelectric Mount , 2005 .

[39]  Anuradha M. Annaswamy,et al.  Robust Adaptive Control , 1984, 1984 American Control Conference.

[40]  Jonathan Millitzer,et al.  Development of Active Engine Mounts Based on Piezo Actuators , 2014, ATZ worldwide.

[41]  Sanjiv G. Tewani,et al.  Active Vibration and Noise Cancellation Control of Four Cylinder Engines - An Application , 1995 .

[42]  Peter Pfeffer,et al.  Non-Linear Modeling of Bushings and Cab Mounts for Calculation of Durability Loads , 2014 .

[43]  A. Hall,et al.  Adaptive Switching Circuits , 2016 .

[44]  Peter E. Pfeffer,et al.  Simple non-linear model for elastomer and hydro-mountings to optimise overall vehicle simulation , 2002 .

[45]  Nader Vahdati,et al.  Development of an Electromagnetic Active Engine Mount , 2015 .

[46]  S. Lambertz.  Nichtlineares Materialgesetz für technische Gummiwerkstoffe mit deformationsabhängigen Eigenschaften und seine experimentelle Überprüfung an Gummifederelementen , 1994 .

[47]  Marcelo J. Dapino,et al.  Coupled axisymmetric finite element model of a magneto-hydraulic actuator for active engine mounts , 2011, Smart Structures and Materials + Nondestructive Evaluation and Health Monitoring.

[48]  Li Sui,et al.  Piezoelectric Actuator Design and Application on Active Vibration Control , 2012 .

[49]  Seung-Bok Choi,et al.  Design and vibration control of vehicle engine mount activated by MR fluid and piezoelectric actuator , 2009, International Conference on Smart Materials and Nanotechnology in Engineering.

[50]  Hideki Matsuoka,et al.  Development of New Intelligent Tourer : 2004 Model INSPIRE , 2006 .

[51]  André Gennesseaux.  Research for New Vibration Isolation Techniques: From Hydro-Mounts to Active Mounts , 1993 .

[52]  Leon M Keer,et al.  Modelling of a hydraulic engine mount focusing on response to sinusoidal and composite excitations , 1995 .

[53]  Michael F. Shlesinger,et al.  Time‐Scale Invariance in Transport and Relaxation , 1991 .

[54]  M. Tiwari,et al.  Experimental characterization of a nonlinear hydraulic engine mount , 2003 .

[55]  Amir Khajepour,et al.  Non-Linear Modelling of Hydraulic Mounts: Theory and Experiment , 2002 .

[56]  Arjon Turnip,et al.  Sensorless Control with Kalman Filter in an Active Engine Mount System , 2015, 2015 6th International Conference on Intelligent Systems, Modelling and Simulation.

[57]  Hua Xin,et al.  Active Engine Vibration Isolation Using Robust Control , 2013 .

[58]  T. Lewis.  The Effects of Dynamic Strain Amplitude and Static Prestrain on the Properties of Viscoelastic Materials , 1991 .

[59]  Michel Verhaegen,et al.  Robustness of the Filtered-X LMS Algorithm— Part II: Robustness Enhancement by Minimal Regularization for Norm Bounded Uncertainty , 2007, IEEE Transactions on Signal Processing.

[60]  Xiao-kang Wei,et al.  An Improved PID Controller Based on Particle Swarm Optimization for Active Control Engine Mount , 2017 .

[61]  Hideki Matsuoka,et al.  NV countermeasure technology for a cylinder-on-demand engine - : Development of active control engine mount , 2004 .

[62]  H. J. Taylor.  The New Generation of Engine Mounts , 1986 .

[63]  Seung-Bok Choi,et al.  A new robust adaptive controller for vibration control of active engine mount subjected to large uncertainties , 2015 .

[64]  G. B..  The Dynamical Theory of Gases , 1916, Nature.

[65]  Tsutomu Hamabe,et al.  Development of an Active Control Engine Mount System , 1999 .

[66]  Katsuhiro Hirata,et al.  Linear Oscillatory Actuator Using Regenerative Energy , 2013 .

[67]  Jun Gao,et al.  Extended filtered-x-least-mean-squares algorithm for an active control engine mount based on acceleration error signal , 2017 .

[68]  C. Lee,et al.  DYNAMIC ANALYSIS AND CONTROL OF ACTIVE ENGINE MOUNT SYSTEM , 2003 .

[69]  Stefan Vollmann,et al.  Active Engine Mount System In The New Audi S8 , 2013 .

[70]  Douglas A. Swanson.  Active Engine Mounts for Vehicles , 1993 .

[71]  Heidar Ali Talebi,et al.  A Robust Active Vibration Control of Automotive Engine , 2010 .

[72]  Claes Olsson,et al.  Active automotive engine vibration isolation using feedback control , 2006 .

[73]  Boris Lohmann,et al.  H∞ Feedback control and Fx-LMS feedforward control for car engine vibration attenuation , 2005 .

[74]  David P Stoten,et al.  The design and development of a self-tuning active engine mount. , 2000 .

[75]  Markus Rupp,et al.  Experimental and analytical study of secondary path variations in active engine mounts , 2015 .

[76]  Ken Ichiryu,et al.  Study on Hydraulic Active Engine Mount , 2003 .

[77]  Waleed Fekry Faris,et al.  Modelling and Control of Four and Six DOF Active Engine Mount System Using (PID and LQR) , 2014 .

[78]  Zheng Chao Xie,et al.  Design and Optimization on Active Engine Mounting Systems for Vibration Isolation , 2013 .

[79]  Noboru Niguchi,et al.  A New Linear Oscillatory Actuator with Variable Characteristics Using Two Sets of Coils , 2016, Sensors.

[80]  Sai Cheong Fok,et al.  Active force cancellation of a near resonance vibrating system using robust H∞ control , 2012 .

[81]  Dennis R. Morgan,et al.  An analysis of multiple correlation cancellation loops with a filter in the auxiliary path , 1980, ICASSP.

[82]  Clayton A. Maas,et al.  New Two-Step Optimization Process of an Active Engine Mount: Applying DFSS Techniques and Taguchi Methods of Robust Design Strategies: Part I , 2006 .

[83]  Akio Nagamatsu,et al.  Optimum design method for hydraulic engine mount. , 1991 .

[84]  Shi Wen-ku.  Simulation of Vibration Characteristics of Active Controlled Hydraulic Mount with Electrostrictive Actuator , 2005 .

[85]  Shibayama Toshiyuki,et al.  Active Engine Mount for a Large Amplitude of Idling Vibration , 1995 .

[86]  Rajendra Singh,et al.  Linear analysis of automotive hydro-mechanical mount with emphasis on decoupler characteristics , 1992 .

[87]  Peter Pfeffer,et al.  Modellierung von Elastomer- und Hydrolagern zur Simulation von Fahrkomfort und Fahrdynamik / Modelling of elastomer and hydro mounts for ride comfort and handling simulation , 2011 .

[88]  Jae-Cheon Lee,et al.  Identification of optimal control parameters for a pneumatic active engine mount system , 2011, Proceedings of 2011 International Conference on Fluid Power and Mechatronics.

[89]  K. Aoki,et al.  Application of an Active Control Mount(ACM) for Improved Diesel Engine Vehicle Quietness , 1999 .

[90]  D. Stoten,et al.  The error-based minimal control synthesis algorithm with integral action , 2003 .

[91]  Mehrdad Moallem,et al.  Piezo-Actuated Active Decoupler Hydraulic Engine Mount , 2010 .

[92]  V-Q Nguyen,et al.  Sliding mode control of a vibrating system using a hybrid active mount , 2009 .

[93]  Claes Olsson,et al.  Active Engine Vibration Isolation using Feedback Control , 2002 .

[94]  Jonathan Millitzer,et al.  Experimental study on active noise and active vibration control for a passenger car using novel piezoelectric engine mounts and electrodynamic inertial mass actuators , 2014 .

[95]  Ali Hosseini.  A solenoid-based active hydraulic engine mount: modelling, analysis, and verification , 2010 .

[96]  Jianming Yang,et al.  Two-degree-of-freedom controller to reduce the vibration of vehicle engine-body system , 2001, IEEE Trans. Control. Syst. Technol..

[97]  Christian Scheiblegger,et al.  New Nonlinear Bushing Model for Ride Comfort and Handling Simulation: Focussing on Linearization and the Implementation into MBS Environment , 2013 .

[98]  Chong-Won Lee,et al.  PERFORMANCE TEST OF ACTIVE ENGINE MOUNT SYSTEM IN PASSENGER CAR , .

[99]  B. Lohmann,et al.  Haar Wavelet-based Robust Optimal Control for Vibration Reduction of Vehicle Engine–body System , 2007 .

[100]  Min Haitao.  Simulation of Vibration Characteristics of Active Controled Hydraulic Mount with Electrostrictive Actuator , 2005 .

[101]  Bo-Ha Lee,et al.  Model based feed-forward control of electromagnetic type active control engine mount system = 전자석 구동형 능동 엔진 마운트의 모델 기반 제어 , 2009 .

[102]  L. Sievers,et al.  Active Narrow-Band Vibration Isolation Of Machinery Noise From Resonant Substructures , 1993 .

[103]  William B. Conover,et al.  Fighting Noise with Noise , 1956 .

[104]  Rajendra Singh,et al.  Analysis of powertrain motions given a combination of active and passive isolators , 2009 .

[105]  Seung-Bok Choi,et al.  A piezostack-based active mount for broadband frequency vibration control: experimental validation , 2009 .

[106]  Jang-Young Choi,et al.  Design Considerations of Linear Electromagnetic Actuator for Hybrid-Type Active Mount Damper , 2013, IEEE Transactions on Magnetics.

[107]  Katsuhiro Hirata,et al.  Proposal of a Two Movers Linear Oscillatory Actuator for Active Control Engine Mounts , 2013, IEEE Transactions on Magnetics.

[108]  William R. Saunders,et al.  Adaptive Structures: Dynamics and Control , 1998 .

[109]  G. Nakhaie Jazar,et al.  Optimization of Classical Hydraulic Engine Mounts Based on RMS Method , 2005 .

[110]  Rajendra Singh,et al.  Nonlinear Analysis of Automotive Hydraulic Engine Mount , 1993 .

[111]  H.-J Karkosch,et al.  Automotive applications of active vibration control , 1999, 1999 European Control Conference (ECC).

[112]  Ming Li,et al.  A numerical investigation on active engine mounting systems and its optimization , 2014 .

[113]  J. Maxwell.  II. On the dynamical theory of gases , 2022, Proceedings of the Royal Society of London.

[114]  Simon A Neild,et al.  A Minimal Controller Synthesis Algorithm for Narrow-Band Applications , 2005 .

[115]  Michel Verhaegen,et al.  Increasing the robustness of a preconditioned filtered-X LMS algorithm , 2004, IEEE Signal Processing Letters.

[116]  Seonghun Park,et al.  Modeling of a hydraulic engine mount for active pneumatic engine vibration control using the extended Kalman filter , 2009 .

[117]  Amélie Renault.  Modelling of pneumatic engine mount , 2005 .

[118]  Katsuhiro Hirata,et al.  Linear Oscillatory Actuator with Dynamic Vibration Control , 2002 .

[119]  Waleed Fekry Faris,et al.  Active engine mounting controller using extended minimal resource allocating networks , 2008 .

[120]  Hendrik Van Brussel,et al.  Comparison of two-on-line identification algorithms for active noise control , 1993 .

[121]  Abdolreza Ohadi,et al.  Robust control of automotive engine using active engine mount , 2013 .