Anisotropic Mechanical Properties of the MA956 ODS Steel Characterized by the Small Punch Testing Technique

Abstract The small punch testing technique was used to assess both creep and fracture properties of the MA956 oxide dispersion strengthened ferritic steel. The anisotropy in mechanical properties was addressed, as well as the alloy’s susceptibility to thermal embrittlement. Strong anisotropy was found in the material’s creep resistance at 725 °C for longer rupture times. Anisotropic behavior was also observed for the ductile–brittle transition temperature (DBTT). The origin of the anisotropy can be related to the strongly directional microstructure which enables a large amount of intergranular cracking during straining at both high and low temperatures. The DBTT of the alloy is very high, and can be further increased by at least 200 °C after 1000 h of ageing at 475 °C, due to the formation of the Cr-rich α′ phase. The particularly high susceptibility of the MA956 to thermal embrittlement is mainly a consequence of its high chromium content.

[1]  O. Buck,et al.  Development of Small Punch Tests for Ductile-Brittle Transition Temperature Measurement of Temper Embrittled Ni-Cr Steels , 1986 .

[2]  Otto K. Harling,et al.  The development of a miniaturized disk bend test for the determination of postirradiation mechanical properties , 1981 .

[3]  O. Buck,et al.  Evaluation of the ductile-to-brittle transition temperature shift due to temper embrittlement and neutron irradiation by means of a small-punch test , 1986 .

[4]  J. Chao,et al.  On the delamination of FeCrAl ODS alloys , 2009 .

[5]  Y. Z. Li,et al.  Qualification of P91 welds through Small Punch creep testing , 2011 .

[6]  M. Mathon,et al.  Assessment of ODS-14%Cr ferritic alloy for high temperature applications , 2004 .

[7]  E. Alves,et al.  Microstructural characterization of Eurofer-ODS RAFM steel in the normalized and tempered condition and after thermal aging in simulated fusion conditions , 2005 .

[8]  S. D. Norris,et al.  A comparison of the disk bend test and the Charpy impact test for fracture property evaluation of power station steels , 1997 .

[9]  W. R. Corwin,et al.  The use of small scale specimens for testing irradiated materials , 1986 .

[10]  K. F. Russell,et al.  Phase separation in PM 2000™ Fe-base ODS alloy : Experimental study at the atomic level , 2008 .

[11]  J. Isselin,et al.  Anisotropy in tensile and ductile–brittle transition behavior of ODS ferritic steels , 2011 .

[12]  Shigeharu Ukai,et al.  R&D of oxide dispersion strengthened ferritic martensitic steels for FBR , 1998 .

[13]  John P. Shingledecker,et al.  Oxide dispersion-strengthened steels: A comparison of some commercial and experimental alloys , 2005 .

[14]  Concetta Fazio,et al.  Innovative materials for Gen IV systems and transmutation facilities: The cross-cutting research project GETMAT , 2011 .

[15]  N. Muthukumar,et al.  Development of Al added high-Cr ODS steels for fuel cladding of next generation nuclear systems , 2011 .

[16]  David S. Gelles,et al.  Development of oxide dispersion strengthened ferritic steels for fusion , 1996 .

[17]  A. Czyrska-Filemonowicz,et al.  Creep mechanisms of ferritic oxide dispersion strengthened alloys , 2003 .

[18]  C. Jang,et al.  Embrittlement and hardening during thermal aging of high Cr oxide dispersion strengthened alloys , 2007 .

[19]  T. Chou.  Recrystallisation behaviour and grain structure in mechanically alloyed oxide dispersion strengthened MA956 steel , 1997 .

[20]  J. Chakrabarty,et al.  A theory of stretch forming over hemispherical punch heads , 1970 .

[21]  A. Kimura,et al.  Pre- and post-deformation microstructures of oxide dispersion strengthened ferritic steels , 2007 .