Active-clamped ZVS current-fed push–pull isolated dc/dc converter for renewable energy conversion applications

This study introduces a new active-clamped current-fed push-pull dc-dc converter for renewable energy conversion applications. The proposed converter conserves small input current pulsation, high-voltage conversion ratio, zero-voltage switching (ZVS) and zero-current-switching operation for primary switches and rectifier diodes, respectively, over a large load range. Also, the additional active clamping circuit serves to suppress the voltage spike across all primary switches, as well as assists in achieving ZVS operation. So, the low-voltage switches with low on-state resistance can be adopted. These features can reduce switching loss, voltage stress, transformer turns ratio and diode reverse-recovery effect. More importantly, similar characteristics can be obtained with minimised switches compared with the reported converters that enable to reduce the cost and improve the reliability. Detailed steady-state operation, analysis, performance comparison, experimental results and loss breakdown of the proposed converter are fully discussed in this study. Finally, a 520 W prototype verifies the theoretical analysis.

[1]  A. H. Weinberg,et al.  A new zero voltage and zero current power-switching technique , 1989 .

[2]  Takashi Yamashita,et al.  Stability in high-output-voltage push-pull current-fed converters , 1993 .

[3]  Fred C. Lee,et al.  A soft-switched, full-bridge boost converter employing an active-clamp circuit , 1996, PESC Record. 27th Annual IEEE Power Electronics Specialists Conference.

[4]  M. Mangal,et al.  18 kW DC-DC converter using push-pull inverter with lossless snubber circuits , 1996, Proceedings of International Conference on Power Electronics, Drives and Energy Systems for Industrial Growth.

[5]  I. Barbi,et al.  A ZVS clamping mode-current-fed push-pull DC-DC converter , 1998, IEEE International Symposium on Industrial Electronics. Proceedings. ISIE'98 (Cat. No.98TH8357).

[6]  I. Barbi,et al.  A single-switch flyback-current-fed DC-DC converter , 1998 .

[7]  Ivo Barbi,et al.  Isolated DC-DC converters with high-output voltage for TWTA telecommunication satellite applications , 2003 .

[8]  M. Mohr,et al.  Voltage Fed and Current Fed Full Bridge Converter for the Use in Three Phase Grid Connected Fuel Cell Systems , 2006, 2006 CES/IEEE 5th International Power Electronics and Motion Control Conference.

[9]  Chung-Yuen Won,et al.  Fuel Cell Generation System With a New Active Clamping Current-Fed Half-Bridge Converter , 2007, IEEE Transactions on Energy Conversion.

[10]  Jung-Min Kwon,et al.  High-Efficiency Fuel Cell Power Conditioning System With Input Current Ripple Reduction , 2009, IEEE Transactions on Industrial Electronics.

[11]  C. Chu,et al.  Analysis and design of a current-fed zero-voltage-switching and zero-current-switching CL-resonant push-pull dc-dc converter , 2009 .

[12]  Eugene H. Kim,et al.  High step-up resonant push-pull converter with high efficiency , 2009 .

[13]  Esteban Sanchis-Kilders,et al.  High-Efficiency Regulation Method for a Zero-Current and Zero-Voltage Current-Fed Push–Pull Converter , 2011, IEEE Transactions on Power Electronics.

[14]  Pertti Silventoinen,et al.  Design of 10 kW resonant push-pull DC-DC converter for solid oxide fuel cell applications , 2011, Proceedings of the 2011 14th European Conference on Power Electronics and Applications.

[15]  Hui Li,et al.  A Soft Switching Three-phase Current-fed Bidirectional DC-DC Converter With High Efficiency Over a Wide Input Voltage Range , 2012, IEEE Transactions on Power Electronics.

[16]  Akshay Kumar Rathore,et al.  Analysis, Design and Experimental Results of Wide Range ZVS Active-Clamped L-L Type Current-Fed DC/DC Converter for Fuel Cells to Utility Interface , 2012, IEEE Transactions on Industrial Electronics.

[17]  Stephen J. Finney,et al.  Energy recovery snubber circuit for a dc-dc push-pull converter , 2012 .

[18]  Akshay Kumar Rathore,et al.  Comparison of soft-switching voltage-fed and current-fed bi-directional isolated Dc/Dc converters for fuel cell vehicles , 2012, 2012 IEEE International Symposium on Industrial Electronics.

[19]  Kuo-Ching Tseng,et al.  A High Step-Up Converter With a Voltage Multiplier Module for a Photovoltaic System , 2013, IEEE Transactions on Power Electronics.

[20]  Yisheng Yuan,et al.  One zero-voltage-switching three-transistor push-pull converter , 2013 .

[21]  Akshay Kumar Rathore,et al.  Extended Range ZVS Active-Clamped Current-Fed Full-Bridge Isolated DC/DC Converter for Fuel Cell Applications: Analysis, Design, and Experimental Results , 2013, IEEE Transactions on Industrial Electronics.

[22]  Yu-Kang Lo,et al.  Zero-voltage switching current-fed flyback converter for power factor correction application , 2013 .

[23]  Yong-Chae Jung,et al.  Soft-Switching Current-Fed Push–Pull Converter for 250-W AC Module Applications , 2014, IEEE Transactions on Power Electronics.

[24]  Amod C. Umarikar,et al.  High step-up pulse-width modulation DC–DC converter based on quasi-Z-source topology , 2015 .

[25]  Bret Whitaker,et al.  Extending the operational limits of the push-pull converter with SiC devices and an active energy recovery clamp circuit , 2015, 2015 IEEE Applied Power Electronics Conference and Exposition (APEC).

[26]  D. M. Vilathgamuwa,et al.  A Switching Control Strategy for Single- and Dual-Inductor Current-Fed Push–Pull Converters , 2015, IEEE Transactions on Power Electronics.

[27]  Akshay Kumar Rathore,et al.  Impulse Commutated Zero-Current Switching Current-Fed Push–Pull Converter: Analysis, Design, and Experimental Results , 2015, IEEE Transactions on Industrial Electronics.

[28]  Akshay Kumar Rathore,et al.  Naturally Clamped Zero-Current Commutated Soft-Switching Current-Fed Push–Pull DC/DC Converter: Analysis, Design, and Experimental Results , 2015, IEEE Transactions on Power Electronics.

[29]  Viboon Chunkag,et al.  High-voltage gain zero-current switching push–pull resonant converter for small energy sources , 2016 .