Effects of Si/Al molar ratio on strength endurance and volume stability of metakaolin geopolymers subject to elevated temperature

Abstract Good structural performance in a fire scenario necessitates that the structural material possesses chemical stability, deformation resistance and strength endurance. Excellent chemical stability for geopolymers has been reported in literature at a microscale. However, their performance at macroscale has not yet been systematically explored and the underlying mechanisms remain unexplained. In current study, effect of variation in Si/Al molar ratio on the meso- and macro-scale thermal stability of metakaolin geopolymers has been comprehensively investigated to discover the underlying mechanisms governing the performance. Results show that all the geopolymer samples experienced reduction in compressive strengths after exposure to high temperature up to 900 °C. Although, the geopolymer mixes exhibited good chemical stability at microscale, they possessed poor volume stability at mesoscale with very high thermal shrinkage. It was observed that thermal shrinkage induced crack formation dominates the residual strength for geopolymer mixes with Si/Al molar ratio ≤ 1.50, while densification of matrix is the governing factor of the residual strength for geopolymer mixes with Si/Al molar ratio > 1.50. Re-crystallization of nepheline at high temperature adversely affect the strength by inducing expansion and cracking of the geopolymer matrix. Geopolymer sample with Si/Al ratio 1.75 retained highest strength (6 MPa) because viscous sintering of geopolymer mixes with high Si/Al ratio at temperature beyond 600 °C enables localized healing of micro-cracks and densification of matrix which favored compressive strength gain after exposure to 900 °C. At an even higher Si/Al of 2.0, foaming of unreacted silica upon heating can lead to expansion and cracking of the sample which reduce the strength. It was observed that due to high degree of cracking damage and low residual strength retention, it is essential to improve the macro-scale stability of metakaolin geopolymers for structural fire resistance applications.

[1]  Ángel Palomo,et al.  High-Temperature Resistance in Alkali-Activated Cement , 2010 .

[2]  Jadambaa Temuujin,et al.  Assessing the suitability of three Australian fly ashes as an aluminosilicate source for geopolymers in high temperature applications , 2011 .

[3]  T Z Harmathy,et al.  THERMAL PROPERTIES OF CONCRETE AT ELEVATED TEMPERATURES , 1970 .

[4]  Shuai Fu,et al.  Effects of Si/Al ratio on the structure and properties of metakaolin based geopolymer , 2016 .

[5]  J. Davidovits.  Geopolymers and geopolymeric materials , 1989 .

[6]  En-Hua Yang,et al.  Incinerator bottom ash (IBA) aerated geopolymer , 2016 .

[7]  Kwesi Sagoe-Crentsil,et al.  Factors affecting the performance of metakaolin geopolymers exposed to elevated temperatures , 2008 .

[8]  Anja Buchwald,et al.  Sustainable design of geopolymers. Evaluation of raw materials by the integration of economic and environmental aspects in the early phases of material development , 2007 .

[9]  J. Deventer,et al.  The geopolymerisation of alumino-silicate minerals , 2000 .

[10]  K. Tan,et al.  Mix design factors and strength prediction of metakaolin-based geopolymer , 2017 .

[11]  Grant C. Lukey,et al.  The thermal evolution of metakaolin geopolymers: Part 2 – Phase stability and structural development , 2007 .

[12]  A. Adamson.  Physical chemistry of surfaces , 1960 .

[13]  Jay G. Sanjayan,et al.  Effect of elevated temperatures on geopolymer paste, mortar and concrete , 2010 .

[14]  Jadambaa Temuujin,et al.  Preparation and thermal properties of fire resistant metakaolin-based geopolymer-type coatings , 2011 .

[15]  J. Deventer,et al.  Understanding the relationship between geopolymer composition, microstructure and mechanical properties , 2005 .

[16]  W. Rickard,et al.  Performance of fibre reinforced, low density metakaolin geopolymers under simulated fire conditions , 2013 .

[17]  Jay G. Sanjayan,et al.  An investigation of the mechanisms for strength gain or loss of geopolymer mortar after exposure to elevated temperature , 2009 .

[18]  J. Davidovits.  Geopolymers : inorganic polymeric new materials , 1991 .

[19]  Kwesi Sagoe-Crentsil,et al.  Comparative performance of geopolymers made with metakaolin and fly ash after exposure to elevated temperatures , 2007 .

[20]  Kenneth J. D. MacKenzie,et al.  Thermal behaviour of inorganic geopolymers and composites derived from sodium polysialate , 2003 .

[21]  J. Deventer,et al.  Geopolymers : structure, processing, properties and industrial applications , 2009 .

[22]  Yu Zhou,et al.  Thermal evolution and crystallization kinetics of potassium-based geopolymer , 2011 .

[23]  W. Rickard,et al.  Fire-Resistant Geopolymers: Role of Fibres and Fillers to Enhance Thermal Properties , 2014 .

[24]  W. Rickard,et al.  15 – Thermal properties of geopolymers , 2009 .

[25]  J. Deventer,et al.  Thermal evolution of metakaolin geopolymers: Part 1 – Physical evolution , 2006 .

[26]  John L. Provis,et al.  Activating solution chemistry for geopolymers , 2009 .

[27]  John L. Provis,et al.  Dilatometry of geopolymers as a means of selecting desirable fly ash sources , 2012 .

[28]  V. Farmer.  The Infrared spectra of minerals , 1974 .

[29]  Peter Duxson,et al.  Evolution of gel structure during thermal processing of Na-geopolymer gels. , 2006, Langmuir : the ACS journal of surfaces and colloids.

[30]  Jay G. Sanjayan,et al.  Geopolymer and Portland cement concretes in simulated fire , 2011 .

[31]  Grant C. Lukey,et al.  Physical evolution of Na-geopolymer derived from metakaolin up to 1000 °C , 2007 .

[32]  T. Cheng,et al.  Fire-resistant geopolymer produced by granulated blast furnace slag , 2003 .

[33]  James W Giancaspro,et al.  Use of Inorganic Polymer to Improve the Fire Response of Balsa Sandwich Structures , 2006 .

[34]  K. MacKenzie,et al.  Synthesis and thermal behaviour of potassium sialate geopolymers , 2003 .

[35]  P. Duxson,et al.  Effect of Alkali Cations on Aluminum Incorporation in Geopolymeric Gels , 2005 .

[36]  A. Fernández-Jiménez,et al.  New Cementitious Materials Based on Alkali-Activated Fly Ash: Performance at High Temperatures , 2008 .

[37]  J. Deventer,et al.  The Role of Inorganic Polymer Technology in the Development of ‘Green Concrete’ , 2007 .

[38]  P. Balaguru,et al.  FIRE RESISTANT ALUMINOSILICATE COMPOSITES , 1997 .

[39]  Erich D. Rodríguez,et al.  Mechanical and thermal characterisation of geopolymers based on silicate-activated metakaolin/slag blends , 2011, Journal of Materials Science.

[40]  T. Z. Harmathy,et al.  Fire safety design and concrete , 1993 .

[41]  W. Rickard,et al.  Performance of solid and cellular structured fly ash geopolymers exposed to a simulated fire , 2014 .

[42]  C. Kaps,et al.  Stabilised foam clay material with high performance thermal insulation properties , 2004 .