Evaluation of rate-dependent hardening behaviors of AHSS sheets with novel tension and compression test devices

[1]  H. Huh,et al.  Tension/compression hardening behaviors of auto-body steel sheets at intermediate strain rates , 2016 .

[2]  H. Huh,et al.  Rate-dependent hardening model for polymer-bonded explosives with an HTPB polymer matrix considering a wide range of strain rates , 2015 .

[3]  H. Huh,et al.  Evaluation of dynamic hardening models for BCC, FCC, and HCP metals at a wide range of strain rates , 2014 .

[4]  R. H. Wagoner,et al.  A sheet tension/compression test for elevated temperature , 2012 .

[5]  H. Huh,et al.  Tension/compression test of auto-body steel sheets with the variation of the pre-strain and the strain rate , 2011 .

[6]  Hoon Huh,et al.  Dynamic hardening equation of the auto-body steel sheet with the variation of temperature , 2011 .

[7]  C. Park,et al.  Correlation of microscopic structures to the strain rate hardening of SPCC steel , 2010 .

[8]  Kwansoo Chung,et al.  Springback prediction of TWIP automotive sheets , 2009 .

[9]  Kwansoo Chung,et al.  Experimental and numerical investigation of combined isotropic-kinematic hardening behavior of sheet metals , 2009 .

[10]  Hoon Huh,et al.  High speed tensile test of steel sheets for the stress-strain curve at the intermediate strain rate , 2009 .

[11]  Hoon Huh,et al.  Dynamic tensile characteristics of TRIP-type and DP-type steel sheets for an auto-body , 2008 .

[12]  R. H. Wagoner,et al.  Constitutive modeling for anisotropic/asymmetric hardening behavior of magnesium alloy sheets , 2008 .

[13]  Jian Cao,et al.  Experimental and Numerical Investigation of Kinematic Hardening Behavior in Sheet Metals , 2007 .

[14]  R. H. Wagoner,et al.  Hardening evolution of AZ31B Mg sheet , 2007 .

[15]  Frédéric Barlat,et al.  Continuous, large strain, tension/compression testing of sheet material , 2005 .

[16]  Kwansoo Chung,et al.  Spring-back evaluation of automotive sheets based on isotropic-kinematic hardening laws and non-quadratic anisotropic yield functions , 2005 .

[17]  R. H. Wagoner,et al.  Measurements of anisotropic yielding, bauschinger and transient behavior of automotive dual-phase steel sheets , 2003 .

[18]  Fusahito Yoshida,et al.  Elastic-plastic behavior of steel sheets under in-plane cyclic tension-compression at large strain , 2002 .

[19]  R. H. Wagoner,et al.  Role of plastic anisotropy and its evolution on springback , 2002 .

[20]  Vijaykumar Balakrishnan,et al.  Measurement of in-plane Bauschinger effect in metal sheets , 1999 .

[21]  Zheng Tan,et al.  The Bauschinger effect in compression-tension of sheet metals , 1994 .

[22]  R. H. Wagoner,et al.  Effect of stress-strain-law transients on formability , 1986 .

[23]  H. Margolin,et al.  Bauschinger effect during cyclic straining of two ductile phase alloys , 1979 .

[24]  L. Brown.  Orowan's explanation of the Bauschinger effect , 1977 .

[25]  T. E. Davidson,et al.  The Bauschinger Effect in a High-Strength Steel , 1966 .