Proposed flux-based optimization method for determination of minimum superconductor material in shield-type superconducting fault current limiters

Distributed power generation and an ever growing load demand have caused the current level of fault to exceed the nominal rating of power system devices, and fault current limiters are needed even more. The Superconducting Fault Current Limiter, SFCL, forms an efficient category of current limiters. The superconductor part in SFCLs is the most costly part of the device, and minimizing its volume, while maintaining the required characteristics of the device, would be very beneficial. In this work, using a Simulated Annealing optimization algorithm, a method has been proposed to determine minimum required bulk superconductor material in inductive shield-type SFCL structures. The flux linkage balance, generated by the superconductor bulk and copper winding (being the base of the optimization process), has been formulated versus dimensions. The optimum dimensions of the bulk superconductor in a model SFCL, having a limitation current of 3A, are determined using the proposed algorithm. A prototype has been fabricated using determined dimensions, and is tested in an experimental circuit by applying different types of faults. These experimental results demonstrated satisfactory limiting characteristics of the fabricated SFCL. The optimum volume of the bulk superconductor material needed for fabrication of larger scale SFCLs has been calculated and compared with the volume of superconductors employed in worldwide SFCL projects.

[1]  J. Bock,et al.  Performance of an inductive fault current limiter employing BSCCO superconducting cylinders , 1999, IEEE Transactions on Applied Superconductivity.

[2]  V. Plechacek,et al.  The use of the Bi-2223 superconducting tubes , 1997, IEEE Transactions on Applied Superconductivity.

[3]  S. Ramo,et al.  Fields and Waves in Communication Electronics , 1966 .

[4]  Y. Brissette,et al.  Design considerations for an inductive high T/sub c/ superconducting fault current limiter , 1993, IEEE Transactions on Applied Superconductivity.

[5]  Tae Kuk Ko,et al.  A variation of impedance of a high-Tc superconducting fault current limiter with an open core , 2002 .

[6]  J Smith,et al.  Exploring the IEEE C37.234 Guide for Protective Relay Application to Power System Buses , 2011, IEEE Transactions on Power Delivery.

[7]  I. Vajda,et al.  Superconducting FCL: design and application , 2004, IEEE Transactions on Applied Superconductivity.

[8]  T. Janowski,et al.  The 15 kV Class Inductive SFCL , 2010, IEEE Transactions on Applied Superconductivity.

[9]  J. Kozak,et al.  Experimental and Numerical Analysis of Electrothermal and Mechanical Phenomena in HTS Tube of Inductive SFCL , 2006, IEEE Transactions on Applied Superconductivity.

[10]  D. Ito,et al.  Applicability of high T/sub c/ superconducting bulk to superconducting fault current limiting device , 1996 .

[11]  H. Yamaguchi,et al.  Current limiting characteristics of transformer type superconducting fault current limiter , 2005, IEEE Transactions on Applied Superconductivity.

[12]  E. M. Leung,et al.  Superconducting fault current limiters , 2000 .

[13]  Y. Brissette,et al.  Testing and modelling of inductive superconducting fault current limiters , 1997, IEEE Transactions on Applied Superconductivity.

[14]  Toshiro Matsumura,et al.  Inductive type fault current limiter with Bi-2223 thick film on a MgO cylinder , 2003 .

[15]  E.R. Filho,et al.  Test Results of a Superconducting FCL Using Bifilar Coil of BSCCO-2212 , 2006, IEEE Transactions on Applied Superconductivity.

[16]  H. Kado,et al.  Performance of a high-Tc superconducting fault current limiter-design of a 6.6 kV magnetic shielding type superconducting fault current limiter , 1997, IEEE Transactions on Applied Superconductivity.

[17]  A. Morandi,et al.  Magnetic-shield-type fault current limiter equivalent circuit , 2004, IEEE Transactions on Applied Superconductivity.

[18]  H. Yamaguchi,et al.  Current Limiting Characteristics of Transformer Type Superconducting Fault Current Limiter With Shunt Impedance and Inductive Load , 2008, IEEE Transactions on Applied Superconductivity.

[19]  Ok-Bae Hyun,et al.  Design and characteristic analysis of a rod type high-Tc superconducting fault current limiter through electromagnetic analysis , 2001 .

[20]  M. Ichikawa,et al.  A magnetic shielding type superconducting fault current limiter using a Bi2212 thick film cylinder , 1995, IEEE Transactions on Applied Superconductivity.

[21]  K. Koyanagi,et al.  Design and Test Results of a Fault Current Limiter Coil Wound With Stacked YBCO Tapes , 2008, IEEE Transactions on Applied Superconductivity.

[22]  A. Usoskin,et al.  Inductive Fault Current Limiters: Kinetics of Quenching and Recovery , 2009, IEEE Transactions on Applied Superconductivity.

[23]  M. Steurer,et al.  Fault current limiters - R&D status of two selected projects and emerging utility integration issues , 2004, IEEE Power Engineering Society General Meeting, 2004..

[24]  H. Yamaguchi,et al.  Characteristics analysis of transformer type superconducting fault current limiter , 2004, IEEE Transactions on Applied Superconductivity.

[25]  M. Steurer,et al.  A generic real-time computer Simulation model for Superconducting fault current limiters and its application in system protection studies , 2005, IEEE Transactions on Applied Superconductivity.

[26]  J. Kozak,et al.  Design and testing of 230 V inductive type of Superconducting Fault Current Limiter with an open core , 2005, IEEE Transactions on Applied Superconductivity.

[27]  Jakob Rhyner,et al.  Test of 1.2 MVA high- superconducting fault current limiter , 1997 .

[28]  Jakob Rhyner,et al.  1.2 MVA High-Tc Superconducting Fault Current Limiter , 1998 .

[29]  J. Rhyner,et al.  Tests of 100 kW High-T/sub c/ superconducting fault current limiter , 1995, IEEE Transactions on Applied Superconductivity.