Porosity induced fatigue damage of laser welded 7075-T6 joints investigated via synchrotron X-ray microtomography

Abstract The interaction between the pores and the fatigue damage in 7075-T6 joints was characterised via high resolution synchrotron radiation X-ray microcomputed tomography. The spatial distribution and growth behaviour of the pores were investigated and quantified. The gas porosity inside 7075-T6 hybrid welds was found to play a significant role in the fatigue crack nucleation and propagation process. The volume fraction and the total number of pores increased slightly with increasing number of fatigue cycles, which provides a key indicator for the damage evolution. Experimental results indicate that the micropores grew and distorted during fatigue cyclic loading, eventually resulting in fatigue cracks. Under cyclic loads, the maximum micropore is usually not a favourable site, in terms of physical suitability, for fatigue crack initiation and propagation, and the diameter of the cracked pores is in the range of 10–100 μm.

[1]  Philip J. Withers,et al.  In situ analysis of cracks in structural materials using synchrotron X-ray tomography and diffraction , 2006 .

[2]  T. Morgeneyer,et al.  Damage observation in a high-manganese austenitic TWIP steel by synchrotron radiation computed tomography , 2010 .

[3]  M. Preuss,et al.  Fatigue and Damage in Structural Materials Studied by X-Ray Tomography , 2012 .

[4]  Ian Sinclair,et al.  A 3D measurement procedure for internal local crack driving forces via synchrotron X-ray microtomography , 2004 .

[5]  K. Uesugi,et al.  Three-dimensional fatigue crack growth behavior in an aluminum alloy investigated with in situ high-resolution synchrotron X-ray microtomography , 2009 .

[6]  Philip J. Withers,et al.  High Resolution X-ray Tomography of Short Fatigue Crack Nucleation in Austempered Ductile Cast Iron , 2004 .

[7]  A. Takeuchi,et al.  Statistical assessment of fatigue crack initiation from sub-surface hydrogen micropores in high-quality die-cast aluminum , 2011 .

[8]  A. Matsunawa.  Problems and solutions in deep penetration laser welding , 2001 .

[9]  K. Uesugi,et al.  Three-dimensional visualization of ductile fracture in an Al–Si alloy by high-resolution synchrotron X-ray microtomography , 2008 .

[10]  Peter Cloetens,et al.  Characterization of internal damage in a MMCp using X-ray synchrotron phase contrast microtomography , 1999 .

[11]  Henry Proudhon,et al.  Three-dimensional visualisation of fatigue cracks in metals using high resolution synchrotron X-ray micro-tomography , 2006 .

[12]  A. Chabod,et al.  Microtomographic study and finite element analysis of the porosity harmfulness in a cast aluminium alloy , 2011 .

[13]  N. Chawla,et al.  Quantifying the effect of porosity on the evolution of deformation and damage in Sn-based solder joints by X-ray microtomography and microstructure-based finite element modeling , 2012 .

[14]  Peter Cloetens,et al.  Study of the interaction of a short fatigue crack with grain boundaries in a cast Al alloy using X-ray microtomography , 2003 .

[15]  T. C. Lindley,et al.  Quantification of the interaction within defect populations on fatigue behavior in an aluminum alloy , 2009 .

[16]  B. Carlson,et al.  Improving aluminum resistance spot welding in automotive structures , 2013 .

[17]  L. Zhao,et al.  Prevention of porosity by oxygen addition in fibre laser and fibre laser–GMA hybrid welding , 2014 .

[18]  H. W. Kerr,et al.  Weldability of 1.6 mm thick aluminium alloy 5182 sheet by single and dual beam Nd: YAG laser welding , 2003 .

[19]  J. Ion,et al.  Laser beam welding of wrought aluminium alloys , 2000 .

[20]  K. Koyama,et al.  Healing behavior of preexisting hydrogen micropores in aluminum alloys during plastic deformation , 2009 .

[21]  Yukitaka Murakami,et al.  Material defects as the basis of fatigue design , 2012 .

[22]  S. Stock.  Recent advances in X-ray microtomography applied to materials , 2008 .

[23]  L. Tsay,et al.  The influence of porosity on the fatigue crack growth behavior of Ti–6Al–4V laser welds , 2006 .

[24]  C. Chou,et al.  Hot cracking of welds on heat treatable aluminium alloys , 2005 .

[25]  Eric Maire,et al.  In situ observation of ductile fracture using X-ray tomography technique , 2011 .

[26]  K. Uesugi,et al.  Three-Dimensional Visualization of the Interaction between Fatigue Crack and Micropores in an Aluminum Alloy Using Synchrotron X-Ray Microtomography , 2007 .

[27]  K. Uesugi,et al.  Direct measurement procedure for three-dimensional local crack driving force using synchrotron X-ray microtomography , 2008 .

[28]  G. G. Stokes.  "J." , 1890, The New Yale Book of Quotations.

[29]  E. Maire,et al.  Experimental study of porosity and its relation to fatigue mechanisms of model Al–Si7–Mg0.3 cast Al alloys , 2001 .

[30]  Henry Proudhon,et al.  Three-dimensional characterisation and modelling of small fatigue corner cracks in high strength Al-alloys , 2012 .

[31]  Anthony Gravouil,et al.  Fatigue crack propagation: In situ visualization using X-ray microtomography and 3D simulation using the extended finite element method , 2006 .