Butt autogenous laser welding of AA 2024 aluminium alloy thin sheets with a Yb:YAG disk laser

Higher productivity, lower distortion and better penetration are the main advantages provided by laser welding in comparison with conventional processes. A Trumpf TruDisk 2002 Yb:YAG disk laser is used in this work to increases productivity and quality. Aluminium alloys lead to many technological issues in laser welding, resulting in shallow penetration and defects. In particular, AA 2024 aluminium alloy in a thin sheet is investigated in this paper, being it is used extensively in the automotive and aerospace industries. Bead-on-plate and butt autogenous laser welding tests with continuous wave emission on 1.25 mm thick AA 2024 aluminium alloy sheets were examined morphologically and micro-structurally. The geometric and mechanical features of the welding bead were evaluated via a three-level experimental plan. In addition to the power and speed which are traditionally referred to, beam defocusing was considered as an additional governing factor in a central composite design scheme because it massively affects keyhole conditions. Softening in the fused zone is discussed via Vickers micro-hardness testing and magnesium loss through energy dispersive spectrometry. After properly performing the modelling and optimisation of the fused zone and the cross-section shape factor as the response variables, the laser welding conditions for thin sheets of AA 2024 aluminium alloy are suggested. X-ray and tensile tests were conducted on the specimens obtained with the recommended processing parameters to characterise the AA 2024 disk laser welded beads.

[1]  F. Caiazzo,et al.  Porosity evolution in aluminum alloy 2024 bop and butt defocused welding by Yb-YAG disk laser , 2011 .

[2]  F. Botana,et al.  Laser welding of aluminium alloys 5083 and 6082 under conduction regime , 2009 .

[3]  G. Derringer,et al.  Simultaneous Optimization of Several Response Variables , 1980 .

[4]  S. Kalita.  Microstructure and corrosion properties of diode laser melted friction stir weld of aluminum alloy 2024 T351 , 2011 .

[5]  A. Giesen,et al.  Fifteen Years of Work on Thin-Disk Lasers: Results and Scaling Laws , 2007, IEEE Journal of Selected Topics in Quantum Electronics.

[6]  T. DebRoy,et al.  Porosity, underfill and magnesium loss during continuous wave Nd:YAG laser welding of thin plates of aluminum alloys 5182 and 5754 , 1999 .

[7]  S. R. Rajesh,et al.  Microstructure and Mechanical properties of Hybrid Laser-Friction Stir Welding between AA6061-T6 Al alloy and AZ31 Mg alloy , 2011 .

[8]  F. Caiazzo,et al.  Investigation on Porosity Content in 2024 Aluminum Alloy Welding by Yb:YAG Disk Laser , 2011 .

[9]  P. Peyre,et al.  Reduction of porosity content generated during Nd:YAG laser welding of A356 and AA5083 aluminium alloys , 2003 .

[10]  Giuseppe Daurelio,et al.  Laser welding of the AA 2024-T3 aluminum alloy by using two different laser sources (Nd:YAG or CO2) , 2005, International Symposium on High Power Laser Systems and Applications.

[11]  Jungho Cho,et al.  Weldability during the laser lap welding of Al 5052 sheets , 2008 .

[12]  P. Withers,et al.  Physically-based constitutive modelling of residual stress development in welding of aluminium alloy 2024 , 2004 .

[13]  David Burns,et al.  Progress towards high-power, high-brightness neodymium-based thin-disk lasers , 2004 .

[14]  E. Capello.  Le Lavorazioni Industriali Mediante Laser di Potenza , 2003 .

[15]  W. Steen.  Laser Material Processing , 1991 .

[16]  Yuh J. Chao,et al.  Heat Transfer in Friction Stir Welding—Experimental and Numerical Studies , 2003 .

[17]  I. Richardson,et al.  Autogenous laser keyhole welding of aluminum alloy 2024 , 2005 .

[18]  Keng H. Leong,et al.  Laser welding of aluminum alloys , 1997, Photonics West.

[19]  A. Scialpi,et al.  Influence of shoulder geometry on microstructure and mechanical properties of friction stir welded 6082 aluminium alloy , 2007 .

[20]  F. Hajiesmaeilbaigi,et al.  Optimizing the Yb:YAG thin disc laser design parameters , 2008 .

[21]  Joseph R. Davis,et al.  Special Features of Structure Formation and Properties of Special High-Alloy Alloys of the Al – Si – Cu System , 2023, Metal Science and Heat Treatment.

[22]  S. C. Du Plessis,et al.  Physical Metallurgy 2 , 2014 .

[23]  Jamshid Sabbaghzadeh,et al.  The relation between liquation and solidification cracks in pulsed laser welding of 2024 aluminium alloy , 2009 .

[24]  Agah Uguz,et al.  Tensile properties of friction stir welded joints of 2024 aluminum alloys in different heat-treated-state , 2009 .