Improving quality and machining efficiency of hole during AlN trepanning with nanosecond pulse laser

[1]  M. H. Fernandes,et al.  Femtosecond laser microstructuring of alumina toughened zirconia for surface functionalization of dental implants , 2020 .

[2]  Jieshi Chen,et al.  A processing technology of grooves by picosecond ultrashort pulse laser in Ni alloy: Enhancing efficiency and quality , 2019, Optics & Laser Technology.

[3]  Yang Wang,et al.  Surface ablation properties and morphology evolution of K24 nickel based superalloy with femtosecond laser percussion drilling , 2019, Optics and Lasers in Engineering.

[4]  S. Dimov,et al.  Drilling of micron-scale high aspect ratio holes with ultra-short pulsed lasers: Critical effects of focusing lenses and fluence on the resulting holes’ morphology , 2018, Optics and Lasers in Engineering.

[5]  W. Hsiao,et al.  Multi-performance characterization analysis of diameter and taper angle on alumina ceramic via using pulsed ultraviolet laser percussion drilling method , 2017 .

[6]  R. Roy,et al.  The effect of trepanning speed of laser drilled acute angled cooling holes on the high temperature low cycle corrosion fatigue performance of CMSX-4 at 850 °C , 2017 .

[7]  Chengyong Wang,et al.  Laser drilling of structural ceramics—A review , 2017 .

[8]  Avanish Kumar Dubey,et al.  Modeling and optimization of geometrical characteristics in laser trepan drilling of titanium alloy , 2016 .

[9]  R. Hellmann,et al.  Rapid micro hole laser drilling in ceramic substrates using single mode fiber laser , 2015 .

[10]  Zhiguo Wu,et al.  Temperature-dependent growth, photoluminescence and ferromagnetic properties of Co-doped AlN hexagonal nanostructures , 2015 .

[11]  A. K. Dubey,et al.  Quality Improvement by Parameter Optimization in Laser Trepan Drilling of Superalloy Sheet , 2014 .

[12]  Y. Tsai,et al.  Parametric effects on femtosecond laser ablation of Al2O3 ceramics , 2013 .

[13]  Urs Eppelt,et al.  Review on laser drilling I. Fundamentals, modeling, and simulation , 2013 .

[14]  Yi-jian Jiang,et al.  An experimental and numerical study on laser percussion drilling of thick-section alumina , 2012 .

[15]  W. Ding,et al.  The Impact of Laser Drilling on AlN Ceramics , 2011, 2011 IEEE International Conference on Information and Automation.

[16]  F. Xiao,et al.  Effects of nano-AlN and sintering atmosphere on microstructure and properties of vitrified bond , 2011 .

[17]  Pengfei Wang,et al.  Fabrication of high thermal conductive Al-cBN ceramic sinters by high temperature high pressure method , 2011 .

[18]  Lianyu Fu,et al.  Experimental study on drilling force in printed circuit board micro drilling process , 2011 .

[19]  Wenying Zhou.  Thermal and dielectric properties of the AlN particles reinforced linear low-density polyethylene composites , 2011 .

[20]  J. L. Tan,et al.  Femtosecond laser drilling of alumina ceramic substrates , 2010 .

[21]  Alberto Reatti,et al.  Design and optimization of a printed circuit board for a photovoltaic and thermal linear solar concentrator , 2009, 2009 13th European Conference on Power Electronics and Applications.

[22]  Ik-Bu Sohn,et al.  Ablation characteristics of aluminum oxide and nitride ceramics during femtosecond laser micromachining , 2009 .

[23]  L. Yate,et al.  Composition and mechanical properties of AlC, AlN and AlCN thin films obtained by r.f. magnetron sputtering , 2009 .

[24]  N. N. Nedialkov,et al.  Analysis of surface and material modifications caused by laser drilling of AlN ceramics , 2007 .

[25]  Winco K. C. Yung,et al.  Nd:YAG laser drilling in epoxy resin/AlN composites material , 2007 .

[26]  Wen-Tung Chien,et al.  Investigating the recast layer formed during the laser trepan drilling of Inconel 718 using the Taguchi method , 2007 .

[27]  Friedrich Dausinger,et al.  Laser drilling in thin materials with bursts of ns-pulses generated by stimulated Brillouin scattering (SBS) , 2005 .

[28]  Yue Jiao,et al.  Rotary ultrasonic machining of ceramic matrix composites: feasibility study and designed experiments , 2005 .

[29]  F. Varas,et al.  Theoretical analysis of material removal mechanisms in pulsed laser fusion cutting of ceramics , 2005 .

[30]  J. Jones,et al.  Melt ejection during laser drilling of metals , 2003 .

[31]  D. Guo,et al.  Spatter-free laser drilling of alumina ceramics based on gelcasting technology , 2003 .

[32]  Minoru Obara,et al.  Selective ablation of AlN ceramic using femtosecond, nanosecond, and microsecond pulsed laser , 2001 .

[33]  Michael W.S. Lau,et al.  A technical review of the laser drilling of aerospace materials , 1994 .

[34]  Jiwang Yan,et al.  Nanosecond pulsed laser irradiation of sapphire for developing microstructures with deep V-shaped grooves , 2018 .

[35]  H. Qi,et al.  Micromachining of Metals and Thermal Barrier Coatings using a 532 nm Nanosecond Fiber Laser , 2012 .

[36]  F. Zhao,et al.  High aspect ratio micro-hole drilling aided with ultrasonic vibration and planetary movement of electrode by micro-EDM , 2009 .

[37]  Takahisa Masuzawa,et al.  State of the Art of Micromachining , 2000 .