Active disassembly applied to end of life vehicles

Active Disassembly is technology that has been developed to allow assemblies to readily separate for recycling when they are exposed to certain triggering conditions. It is based around fasteners that use `Smart' Materials, typically Shape Memory Alloys (SMA) or Shape Memory Polymers (SMP). This has led to research in the field to be known as Active Disassembly Using Smart Materials (ADSM). Particularly within the context of the EU End of Life Vehicle (ELV) legislation, ADSM has the potential to enable the achievement of the recycling levels required. In this thesis, active disassembly solutions have been developed which have focused on the disassembly of the Instrument Panel, and the glazing within a vehicle. To achieve this, a number of novel Smart fastening devices have been developed, two of which are triggered by integral heating elements. This investigation also led to the creation of a new releasable hook and loop fastening system, known as `Shape Memory Hook and Loop Fasteners' (SM-HALF). SM-HALF is a repositionable fastening system that can be released remotely under a thermal stimulus. Research into the residual energy content of ELV batteries has been a significant part of the investigation. It has been found that it is possible to use the energy from `dead' car batteries to power at least 16 shape-memory alloy devices constructed from 25-micron diameter wire, at End of Life. No external energy input is required for disassembly This research is timely as it provides a means of reclaiming 10% of a vehicle that would otherwise be lost to the shredder. The technology can: increase the number of parts available for recycling and reuse, separate waste streams, decrease shredder residue otherwise destined for landfill and increase economic returns for either the vehicle dismantling yards or shredder operator.

[1]  D. Miller.  The effects of ergonomic stressors on process tool maintenance and utilization , 1998 .

[2]  David Harrison,et al.  Shape memory alloy actuators for active disassembly using ‘smart’ materials of consumer electronic products , 2002 .

[3]  J. D. Chiodo,et al.  Investigations of generic self disassembly using shape memory alloys , 1998, Proceedings of the 1998 IEEE International Symposium on Electronics and the Environment. ISEE - 1998 (Cat. No.98CH36145).

[4]  Nick Jones,et al.  Safe Steering Wheel Airbag Removal Using Active Disassembly , 2002 .

[5]  Jan Chal,et al.  Design for Assembly: Principles and Practice , 1994 .

[6]  Ali K. Kamrani,et al.  Product design for modularity , 2000 .

[7]  David Harrison,et al.  Design for Automotive Glass Removal Using Active Disassembly , 2002 .

[8]  Kari Ullakko,et al.  BASIC PROPERTIES OF MAGNETIC SHAPE MEMORY ACTUATORS , 2002 .

[9]  C. B. Boks,et al.  The relative importance of uncertainty factors in product end-of-life scenarios: A quantification of future developments in design, economy, technology and policy , 2002 .

[10]  J. Perkins,et al.  The Two-Way Shape Memory Effect , 1990 .

[11]  Geoffrey Boothroyd,et al.  Product design for manufacture and assembly , 1994, Comput. Aided Des..

[12]  K. Masui,et al.  Development of products embedded disassembly process based on end-of-life strategies , 1999, Proceedings First International Symposium on Environmentally Conscious Design and Inverse Manufacturing.

[13]  M Anjanappa,et al.  A theoretical and experimental study of magnetostrictive mini-actuators. , 1994 .

[14]  Tadatomo Suga,et al.  Active disassembly and reversible interconnection , 2000, Proceedings of the 2000 IEEE International Symposium on Electronics and the Environment (Cat. No.00CH37082).

[15]  David Harrison,et al.  An initial investigation into active disassembly using shape memory polymers , 2001 .

[16]  N. Warburg,et al.  Accompanying the (re)design of products with environmental assessment (DfE) on the example of ADSM , 2001, Proceedings of the 2001 IEEE International Symposium on Electronics and the Environment. 2001 IEEE ISEE (Cat. No.01CH37190).

[17]  C. M. Wayman,et al.  Shape-Memory Materials , 2018 .

[18]  Kok-Meng Lee,et al.  Modeling and supervisory control of a disassembly automation workcell based on blocking topology , 2000, IEEE Trans. Robotics Autom..

[19]  Surendra M. Gupta,et al.  Design of an integrated component recovery system , 1998, Proceedings of the 1998 IEEE International Symposium on Electronics and the Environment. ISEE - 1998 (Cat. No.98CH36145).

[20]  K. A. Stroud,et al.  Engineering Mathematics , 2020, Nature.

[21]  Richard F. Gordon.  Design Principles for Cu-Zn-Al Actuators , 1990 .

[22]  Surendra M. Gupta,et al.  A Case-Based Reasoning Approach for the Optimal Planning of Disassembly Processes , 2000 .

[23]  Michael E. Henstock,et al.  Design for recyclability , 1988 .

[24]  Measurement of velocity for polymeric fluids by a photochromic flow visualization technique: the tubeless siphon , 1988 .

[25]  M. Singh,et al.  Diversion from landfill: quality products from valuable plastics , 2002 .

[26]  Peter Tautzenberger,et al.  Thermal Actuators: A Comparison of Shape Memory Alloys with Thermostatic Bimetals and Wax Actuators , 1990 .

[27]  K. Kaski,et al.  RAPID COMMUNICATION: Computational studies of compressed and sheared electrorheological fluid , 1996 .

[28]  Graham Jared,et al.  Design for assembly: Influencing the design process , 2000 .

[29]  Nick Jones,et al.  Towards self-disassembling vehicles , 2003 .

[30]  C. Tuck.  Modern battery technology , 1991 .

[31]  K. Otsuka,et al.  Shape-memory materials and phenomena - Fundamental aspects and applications; Proceedings of the Symposium, Boston, MA, Dec. 3-5, 1991 , 1992 .