Numerical simulation and experimental investigation on suction heating of a BOG compressor

Abstract One of the key components of a liquefied natural gas (LNG) receiving terminal is the boil-off gas (BOG) compressor, which is used to pump out the BOG from the LNG storage tank to ensure safety in the transportation and receiving systems. Owing to the ultra-low suction temperature, the heat exchange between the intake gas and the cylinder, piston, and cylinder cover cannot be ignored as in normal conditions. This paper presents an investigation focusing on suction heating of the BOG compressor. A finite element model with dynamic mesh was established to simulate the suction process. At the same time, a performance test rig was built to study the characteristics of the BOG compressor under low suction temperature conditions and verify the numerical model. Consequently, the results of the simulation were in good agreement with experimental results. Both results implied that the temperature of cylinder surface increased starting from the cylinder cover to the crankcase. In addition, at lower suction temperature, the temperature difference between various points on the cylinder surface and cylinder cover was much larger than that at higher suction temperature. With increasing suction temperature, the temperature coefficient increased markedly, and the difference between gas temperatures at the beginning and end of the suction process, as well as the compressor flow rate, decreased significantly; however, the volumetric efficiency increased first and then decreased. Furthermore, the temperature coefficient clearly increased when the compressor rotational speed increased from 250 rpm to 3000 rpm, and it decreased from 0.81 to 0.66 as the pressure ratio increased from 3.0 to 6.0.

[1]  Sangkwon Jeong,et al.  Experimental investigation on convective heat transfer mechanism in a scroll compressor , 2006 .

[2]  Bo Zhang,et al.  3-D finite element simulation of the cylinder temperature distribution in boil-off gas (BOG) compressors , 2012 .

[3]  Huan Wang,et al.  Thermodynamic optimization of the operating parameters for a combined power cycle utilizing low-temperature waste heat and LNG cold energy , 2013 .

[4]  M. S. Chong,et al.  Prediction of Heat and Mass Transfer During Compression in Reciprocating Compressors , 1976 .

[5]  Kim Tiow Ooi,et al.  Heat transfer in compression chamber of a revolving vane (RV) compressor , 2011 .

[6]  Cesar J. Deschamps,et al.  Numerical Analysis of Heat Transfer inside the Cylinder of Reciprocating Compressors in the Presence of Suction and Discharge Processes , 2010 .

[7]  Kim Tiow Ooi.  Heat transfer study of a hermetic refrigeration compressor , 2003 .

[8]  Guohua Shi,et al.  Development status of liquefied natural gas industry in China , 2010 .

[9]  E. Querol,et al.  Boil off gas (BOG) management in Spanish liquid natural gas (LNG) terminals , 2010 .

[10]  Chonghun Han,et al.  Optimization of the Operation of Boil-Off Gas Compressors at a Liquified Natural Gas Gasification Plant , 2007 .

[11]  K. Ooi,et al.  Convective heat transfer in a scroll compressor chamber: a 2-D simulation , 2004 .

[12]  Younggy Shin,et al.  Design of a boil-off natural gas reliquefaction control system for LNG carriers , 2009 .

[13]  T. Morel,et al.  Heat Transfer and Component Temperature Prediction in Reciprocating Compressors , 1988 .

[14]  Alvaro T. Prata,et al.  Heat Transfer Modeling in a Reciprocating Compressor , 1994 .

[15]  Wensheng Lin,et al.  LNG (liquefied natural gas): A necessary part in China's future energy infrastructure , 2010 .

[16]  Liang Pu,et al.  Thermal performance analysis of intermediate fluid vaporizer for liquefied natural gas , 2014 .

[17]  Yiping Dai,et al.  Thermodynamic analysis and optimization of an ammonia-water power system with LNG (liquefied natural gas) as its heat sink , 2013 .

[18]  Cyrus B. Meher-Homji,et al.  Application of Boil Off Gas Compressors in LNG Plants , 2014 .

[19]  R. Liu,et al.  Heat Transfer Between Gas and Cylinder Wall of Refrigerating Reciprocating Compressor , 1984 .