Bi-Gaussian surface identification and reconstruction with revised autocorrelation functions

Abstract The newly proposed continuous separation method for bi-Gaussian stratified surfaces, as the improvement of the existing ISO segmented one, is investigated. The continuous method provides an accurate surface-separation solution but is much more efficient. It has great stability to resist the fluctuations of the probability material ratio curves that are universally observed on real engineering surfaces. In contrast to the ISO segmented method, the continuous one is roughness-scale independent. When using a bi-Gaussian approach, it is difficult to identify component correlation lengths because of missing points in each individual component. An iterative process is used to overcome the defect in determining autocorrelation function (ACF). The ACF quality of the revised bi-Gaussian approach is better than that of the Johnson approach.

[1]  Remigiusz Michalczewski,et al.  The effect of random surface topography height on fretting in dry gross slip conditions , 2014 .

[2]  D. J. Whitehouse,et al.  Surfaces — A Link between Manufacture and Function: , 1978 .

[3]  J. Raja,et al.  Characterization of surface texture generate multi-process manufacture , 1998 .

[4]  Noël Brunetière,et al.  Analysis and Modeling of the Topography of Mechanical Seal Faces , 2010 .

[5]  David J. Whitehouse,et al.  The Generation of Two Dimensional Random Surfaces Having a Specified Function , 1983 .

[6]  Pawel Pawlus,et al.  Abrasive wear resistance of textured steel rings , 2009 .

[7]  Jiunn-Jong Wu.  Simulation of rough surfaces with FFT , 2000 .

[8]  Pawel Pawlus,et al.  Tribological characteristics of one-process and two-process cylinder liner honed surfaces under reciprocating sliding conditions , 2010 .

[9]  Jože Vižintin,et al.  Planning surface texturing for reduced friction in lubricated sliding using surface roughness parameters skewness and kurtosis , 2012 .

[10]  Noël Brunetière,et al.  Stratified Revised Asperity Contact Model for Worn Surfaces , 2017 .

[11]  Vasilios Bakolas,et al.  Numerical generation of arbitrarily oriented non-Gaussian three-dimensional rough surfaces , 2003 .

[12]  Pawel Pawlus,et al.  Comparison of tribological behaviors of one-process and two-process steel surfaces in ball-on-disc tests , 2014 .

[13]  Noël Brunetière,et al.  Stratified effect of continuous bi-Gaussian rough surface on lubrication and asperity contact , 2016 .

[14]  T. R. Thomas.  Computer simulation of wear , 1972 .

[15]  Andreas A. Polycarpou,et al.  Modeling the effect of skewness and kurtosis on the static friction coefficient of rough surfaces , 2004 .

[16]  A. Majumdar,et al.  Fractal characterization and simulation of rough surfaces , 1990 .

[17]  S. E. Leefe.  “Bi-Gaussian” representation of worn surface topography in elastic contact problems , 1998 .

[18]  I. D. Hill,et al.  Fitting Johnson Curves by Moments , 1976 .

[19]  Irene Buj Corral,et al.  Use of roughness probability parameters to quantify the material removed in plateau-honing , 2010 .

[20]  N. L. Johnson,et al.  Systems of frequency curves generated by methods of translation. , 1949, Biometrika.

[21]  Nadir Patir,et al.  A numerical procedure for random generation of rough surfaces , 1978 .

[22]  Noël Brunetière,et al.  Continuous separating method for characterizing and reconstructing bi-Gaussian stratified surfaces , 2016 .

[23]  Pawel Pawlus,et al.  Modeling of worn surface topography formed in a low wear process , 2012 .

[24]  Trevor A Spedding,et al.  The time series modelling of non-gaussian engineering processes , 1982 .

[25]  Jiunn-Jong Wu,et al.  Simulation of non-Gaussian surfaces with FFT , 2004 .

[26]  Mark C. Malburg,et al.  Characterization of Surface Texture Generated by Plateau Honing Process , 1993 .

[27]  K. To̸nder,et al.  Simulation of 3-D random rough surface by 2-D digital filter and fourier analysis , 1992 .

[28]  Pawel Pawlus,et al.  The method of truncation parameters measurement from material ratio curve , 2008 .

[29]  A. Sethuramiah,et al.  Assessment of engine liner wear from bearing area curves , 2000 .

[30]  David J. Whitehouse.  Assessment of Surface Finish Profiles Produced by Multi-Process Manufacture , 1985 .

[31]  Pawel Pawlus,et al.  Simulation of cylinder ‘zero-wear’ process , 2009 .

[32]  Pawel Pawlus,et al.  Simulation of stratified surface topographies , 2008 .