Effect of clad orientation on the mechanical properties of laser-clad repaired ultra-high strength 300 M steel

[1]  S. Palanisamy,et al.  Effect of laser reheat post-treatment on the microstructural characteristics of laser-cladded ultra-high strength steel , 2019, Surface and Coatings Technology.

[2]  Jianjun Li,et al.  In-situ investigation of phase transformation behaviors of 300M steel in continuous cooling process , 2018, Materials Characterization.

[3]  Guang Yang,et al.  Microstructure and tensile properties of laser engineered net shaped reduced activation ferritic/martensitic steel , 2018, Materials Characterization.

[4]  Eduard Hryha,et al.  Effect of build geometry on the microstructural development of 316L parts produced by additive manufacturing , 2018, Materials Characterization.

[5]  S. Palanisamy,et al.  Effect of energy per layer on the anisotropy of selective laser melted AlSi12 aluminium alloy , 2018, Additive Manufacturing.

[6]  M. Easton,et al.  Influence of macrosegregation on solidification cracking in laser clad ultra-high strength steels , 2018 .

[7]  Shu Beng Tor,et al.  Anisotropy and heterogeneity of microstructure and mechanical properties in metal additive manufacturing: A critical review , 2018 .

[8]  Lonnie J. Love,et al.  On the toughness scatter in low alloy C-Mn steel samples fabricated using wire arc additive manufacturing , 2018 .

[9]  M. Easton,et al.  In-situ quench and tempering for microstructure control and enhanced mechanical properties of laser cladded AISI 420 stainless steel powder on 300M steel substrates , 2018 .

[10]  Syed H. Masood,et al.  Effect of scan strategy on density and metallurgical properties of 17-4PH parts printed by Selective Laser Melting (SLM) , 2017 .

[11]  S. Palanisamy,et al.  Metallurgical and geometrical characterisation of the 316L stainless steel clad deposited on a mild steel substrate , 2017 .

[12]  U. Ramamurty,et al.  Mechanical behavior of selective laser melted 316L stainless steel , 2017 .

[13]  Zemin Wang,et al.  Comparison on mechanical anisotropies of selective laser melted Ti-6Al-4V alloy and 304 stainless steel , 2017 .

[14]  A. Elwany,et al.  Mechanical properties and microstructural characterization of selective laser melted 17-4 PH stainless steel , 2017 .

[15]  Peng Guo,et al.  Study on microstructure, mechanical properties and machinability of efficiently additive manufactured AISI 316L stainless steel by high-power direct laser deposition , 2017 .

[16]  Bo Cheng,et al.  Stress and deformation evaluations of scanning strategy effect in selective laser melting , 2016 .

[17]  Hua-ming Wang,et al.  Microstructure characterization and mechanical behavior of laser additive manufactured ultrahigh-strength AerMet100 steel , 2016 .

[18]  Chun H. Wang,et al.  Fatigue and fracture behavior of laser clad repair of AerMet® 100 ultra-high strength steel , 2016 .

[19]  T. Mower,et al.  Mechanical behavior of additive manufactured, powder-bed laser-fused materials , 2016 .

[20]  K. Dawson,et al.  Mechanical response and deformation mechanisms of ferritic oxide dispersion strengthened steel structures produced by selective laser melting , 2015 .

[21]  I. Manna,et al.  Microstructure and Mechanical Properties of Laser Clad and Post-cladding Tempered AISI H13 Tool Steel , 2015, Metallurgical and Materials Transactions A.

[22]  Rui Vilar,et al.  Repair and manufacturing of single crystal Ni-based superalloys components by laser powder deposition—A review , 2015 .

[23]  Thomas Niendorf,et al.  Microstructural Characterization and Mechanical Performance of Hot Work Tool Steel Processed by Selective Laser Melting , 2015, Metallurgical and Materials Transactions B.

[24]  C. Tuck,et al.  Effect of the build orientation on the mechanical properties and fracture modes of SLM Ti–6Al–4V , 2014 .

[25]  Vladimir Luzin,et al.  Effect of laser clad repair on the fatigue behaviour of ultra-high strength AISI 4340 steel , 2014 .

[26]  Jacqueline Lecomte-Beckers,et al.  Microstructures and Mechanical Properties of Stainless Steel AISI 316L Processed by Selective Laser Melting , 2014 .

[27]  Thomas Tröster,et al.  On the fatigue crack growth behavior in 316L stainless steel manufactured by selective laser melting , 2014 .

[28]  S. Aihara,et al.  A simulation model for cleavage crack propagation in bcc polycrystalline solids , 2011 .

[29]  Weidong Huang,et al.  Influence of laser deposition patterns on part distortion, interior quality and mechanical properties by laser solid forming (LSF) , 2011 .

[30]  A. Esnaola,et al.  Study of mechanical properties of AISI 316 stainless steel processed by “selective laser melting”, following different manufacturing strategies , 2010 .

[31]  S. Lynch,et al.  A brief history of fractography , 2006 .

[32]  A. M. Deus,et al.  Rapid tooling by laser powder deposition : Process simulation using finite element analysis , 2005 .

[33]  Gerry Byrne,et al.  Laser cladding of aerospace materials , 2002 .

[34]  F. Prinz,et al.  Thermal stresses and deposition patterns in layered manufacturing , 2001 .

[35]  N. Matthews,et al.  Additive Metal Technologies for Aerospace Sustainment , 2018 .

[36]  Chun H. Wang,et al.  Quantitative fractography and modelling of fatigue crack propagation in high strength AerMet®100 steel repaired with a laser cladding process , 2017 .

[37]  Alaa Elwany,et al.  Effects of building orientation and heat treatment on fatigue behavior of selective laser melted 17-4 PH stainless steel , 2017 .

[38]  S. Aihara,et al.  Simulation of Cleavage Crack Propagation in Steels with Anisotropic Crystal Orientation Distribution , 2014 .

[39]  J. Knott,et al.  Charpy-impact-toughness prediction using an “effective” grain size for thermomechanically controlled rolled microalloyed steels , 2004 .

[40]  Frank W. Liou,et al.  Laser Aided Part Repair-a Review , 2002 .