All-plastic solar cells with a high photovoltaic dynamic range

We report on semitransparent air-processed all-plastic solar cells, fabricated from vacuum-free processes, comprising two polymer electrodes, a polymeric work-function modification layer and a polymer:fullerene photoactive layer. The active layer and the top PEDOT:PSS electrode were prepared by sequential film-transfer lamination on polyethylenimine-modified PEDOT:PSS bottom electrodes. The transferring of films offers ease of layer patterning and the misalignment of defects in the different layers resulting from the additive film transfer lamination process yields high shunt resistance values of 108 ohm cm2. Consequently, all-plastic solar cells fabricated with this process exhibit very low reverse bias dark current and can operate in the photovoltaic quadrant with light irradiance varying over five orders of magnitude. The analysis of the values of the open-circuit voltage as a function of light irradiance over that wide dynamic range points toward an ideality factor of n = 1.82 and a reverse saturation current density of 6.2 × 10−11 A cm−2 for solar cells with an active layer comprised of a blend of poly(3-hexylthiophene) and an indene fullerene bis-adduct.

[1]  Yang Yang,et al.  Polymer solar cells with enhanced open-circuit voltage and efficiency , 2009 .

[2]  Suren A. Gevorgyan,et al.  Scalability and stability of very thin, roll-to-roll processed, large area, indium-tin-oxide free polymer solar cell modules , 2013 .

[3]  M. Wienk,et al.  Efficient Polymer Solar Cells on Opaque Substrates with a Laminated PEDOT:PSS Top Electrode , 2013 .

[4]  M. Chabinyc,et al.  Tail State‐Assisted Charge Injection and Recombination at the Electron‐Collecting Interface of P3HT:PCBM Bulk‐Heterojunction Polymer Solar Cells , 2012 .

[5]  Wei Gong,et al.  High‐Performance Metal‐Free Solar Cells Using Stamp Transfer Printed Vapor Phase Polymerized Poly(3,4‐Ethylenedioxythiophene) Top Anodes , 2012 .

[6]  Mikkel Jørgensen,et al.  All printed transparent electrodes through an electrical switching mechanism: A convincing alternative to indium-tin-oxide, silver and vacuum , 2012 .

[7]  Gang Li,et al.  For the Bright Future—Bulk Heterojunction Polymer Solar Cells with Power Conversion Efficiency of 7.4% , 2010, Advanced materials.

[8]  A. Kahn,et al.  Device Characteristics of Bulk-Heterojunction Polymer Solar Cells are Independent of Interfacial Segregation of Active Layers , 2011 .

[9]  M. Toney,et al.  Modular construction of P3HT/PCBM planar-heterojunction solar cells by lamination allows elucidation of processing-structure-function relationships , 2011 .

[10]  K. Ho,et al.  Fabrication of multilayer organic solar cells through a stamping technique , 2009 .

[11]  Soonil Hong,et al.  Electrostatically Self‐Assembled Nonconjugated Polyelectrolytes as an Ideal Interfacial Layer for Inverted Polymer Solar Cells , 2012, Advanced materials.

[12]  Bernard Kippelen,et al.  Direct correlation between work function of indium-tin-oxide electrodes and solar cell performance influenced by ultraviolet irradiation and air exposure. , 2012, Physical chemistry chemical physics : PCCP.

[13]  Bernard Kippelen,et al.  High performance polymeric charge recombination layer for organic tandem solar cells , 2012 .

[14]  Richard H. Friend,et al.  Efficient Conjugated‐Polymer Optoelectronic Devices Fabricated by Thin‐Film Transfer‐Printing Technique , 2008 .

[15]  Yongfang Li.  Molecular design of photovoltaic materials for polymer solar cells: toward suitable electronic energy levels and broad absorption. , 2012, Accounts of chemical research.

[16]  S. Horng,et al.  Vacuum-free lamination of low work function cathode for efficient solution-processed organic light-emitting diodes , 2012 .

[17]  J. Shim,et al.  Studies of the optimization of recombination layers for inverted tandem polymer solar cells , 2012 .

[18]  Markus Hösel,et al.  Roll-to-roll fabrication of polymer solar cells , 2012 .

[19]  Bernard Kippelen,et al.  Recyclable organic solar cells on cellulose nanocrystal substrates , 2013, Scientific Reports.

[20]  Miao Xu,et al.  Enhanced power-conversion efficiency in polymer solar cells using an inverted device structure , 2012, Nature Photonics.

[21]  Ji-hoon Kim,et al.  High Open Circuit Voltage Solution-Processed Tandem Organic Photovoltaic Cells Employing a Bottom Cell Using a New Medium Band Gap Semiconducting Polymer , 2013 .

[22]  Talha M. Khan,et al.  A Universal Method to Produce Low–Work Function Electrodes for Organic Electronics , 2012, Science.

[23]  Markus Hösel,et al.  All solution processing of ITO-free organic solar cell modules directly on barrier foil , 2012 .

[24]  Jie Zhang,et al.  Efficient Solution‐Processed Small‐Molecule Solar Cells with Inverted Structure , 2013, Advanced materials.

[25]  D. Choi,et al.  Photovoltaic devices with an active layer from a stamping transfer technique: single layer versus double layer. , 2010, Langmuir : the ACS journal of surfaces and colloids.

[26]  Shijun Jia,et al.  Polymer–Fullerene Bulk‐Heterojunction Solar Cells , 2009, Advanced materials.

[27]  B. Kippelen,et al.  Intensity-dependent equivalent circuit parameters of organic solar cells based on pentacene and C60 , 2005 .

[28]  Weiwei Li,et al.  Efficient tandem and triple-junction polymer solar cells. , 2013, Journal of the American Chemical Society.

[29]  D. Choi,et al.  Layer-by-layer all-transfer-based organic solar cells. , 2013, Langmuir : the ACS journal of surfaces and colloids.

[30]  William J. Potscavage,et al.  Critical interfaces in organic solar cells and their influence on the open-circuit voltage. , 2009, Accounts of chemical research.