Development and experimental study of a redundant hybrid machine with five-face milling capability in one setup

[1]  Hyunpyo Shin,et al.  Stiffness enhancement of a redundantly actuated parallel machine tool by dual support rims , 2012 .

[2]  M. T. Masouleh,et al.  Forward kinematic problem of 5-RPUR parallel mechanisms (3T2R) with identical limb structures , 2011 .

[3]  Clément Gosselin,et al.  Singularity analysis of 5-RPUR parallel mechanisms (3T2R) , 2011 .

[4]  Qinchuan Li,et al.  Parasitic motion comparison of 3-PRS parallel mechanism with different limb arrangements , 2011 .

[5]  Hui Zhang,et al.  Design and experimental study of the SPKM165, a five-axis serial-parallel kinematic milling machine , 2011 .

[6]  Chao Wu,et al.  Performance evaluation of parallel manipulators: Motion/force transmissibility and its index , 2010 .

[7]  Liping Wang,et al.  Kinematic calibration of the 3-DOF parallel module of a 5-axis hybrid milling machine , 2010, Robotica.

[8]  Ilian A. Bonev,et al.  Design of a Three-Axis Articulated Tool Head With Parallel Kinematics Achieving Desired Motion/Force Transmission Characteristics , 2010 .

[9]  Hassan Zohoor,et al.  Structural synthesis of 5 DoFs 3T2R parallel manipulators with prismatic actuators on the base , 2010, Robotics Auton. Syst..

[10]  JongWon Kim,et al.  Design and analysis of decoupled parallel mechanism with redundant actuator , 2009 .

[11]  Cha-Soo Jun,et al.  Near net-shape five-axis face milling of marine propellers , 2009 .

[12]  Zhen Huang,et al.  Singularity analysis for six practicable 5-DoF fully-symmetrical parallel manipulators , 2009 .

[13]  Chao Wu,et al.  A new family of spatial 3-DOF parallel manipulators with two translational and one rotational DOFs , 2009, Robotica.

[14]  D. Caldwell,et al.  Geometry and Kinematic Analysis of a Redundantly Actuated Parallel Mechanism That Eliminates Singularities and Improves Dexterity , 2008 .

[15]  Khalifa H. Harib,et al.  A hexapod-based machine tool with hybrid structure: Kinematic analysis and trajectory planning , 2007 .

[16]  Hui Zhao,et al.  A novel 5-DOF fully parallel kinematic machine tool , 2006 .

[17]  Clément Gosselin,et al.  Design and analysis of kinematically redundant parallel manipulators with configurable platforms , 2005, IEEE Transactions on Robotics.

[18]  Xin-Jun Liu,et al.  A new family of spatial 3-DoF fully-parallel manipulators with high rotational capability , 2005 .

[19]  Hsi-Yung Feng,et al.  Configuration analysis of five-axis machine tools using a generic kinematic model , 2004 .

[20]  JongWon Kim,et al.  Kinematic Calibration for Redundantly Actuated Parallel Mechanisms , 2004 .

[21]  Mikael Bäckström,et al.  A direct comparison of the machining performance of a variax 5 axis parallel kinetic machining centre with conventional 3 and 5 axis machine tools , 2003 .

[22]  Hui Zhao,et al.  New kinematic structures for 2-, 3-, 4-, and 5-DOF parallel manipulator designs , 2002 .

[23]  Frank Chongwoo Park,et al.  Design and analysis of a redundantly actuated parallel mechanism for rapid machining , 2001, IEEE Trans. Robotics Autom..

[24]  Frank Chongwoo Park,et al.  Eclipse II: a new parallel mechanism enabling continuous 360-degree spinning plus three-axis translational motions , 2001, IEEE Trans. Robotics Autom..

[25]  K. H. Kim,et al.  A calibration method of redundantly actuated parallel mechanism machines based on projection technique , 2010 .

[26]  Xin-Jun Liu,et al.  Optimal Design and Development of a Decoupled A/B-Axis Tool Head with Parallel Kinematics , 2010 .

[27]  Xin-Jun Liu,et al.  A Micro-positioning Parallel Mechanism Platform with 100-degree Tilting Capability , 2006 .