Powder Recycling Effects on the Tensile and Fatigue Behavior of Additively Manufactured Ti-6Al-4V Parts

Additive manufacturing technology has enabled industries to generate functional parts with an increased level of complexity via layer-by-layer fabrication. In laser-powder bed fusion (L-PBF), powder is often recycled due to its high cost. However, there is no comprehensive study on how powder recycling affects its rheological properties, as well as the mechanical and fatigue behavior of the manufactured part. This study compares powder characteristics and mechanical performance of as-built and machined specimens fabricated from new and heavily used Ti-6Al-4V powder. Powder characteristics include particle size distribution and morphology, flowability, apparent density, compressibility, thermal conductivity, oxygen concentration, and more. Results indicate that particle size distribution becomes narrower and flowability increases with recycling. Not a significant effect of recycling was observed on the monotonic tensile and fatigue behavior of specimens in the as-built surface condition. However, machined specimens fabricated from used powder demonstrated longer fatigue lives in the high cycle regime.

[1]  Ryan R. Dehoff,et al.  Recyclability Study on Inconel 718 and Ti-6Al-4V Powders for Use in Electron Beam Melting , 2016, Metallurgical and Materials Transactions B.

[2]  N. Shamsaei,et al.  Fatigue behavior of Ti-6Al-4V ELI including mean stress effects , 2017 .

[3]  Brian Armstrong,et al.  The Application of Powder Rheology in Additive Manufacturing , 2015 .

[4]  O. Lyckfeldt,et al.  Characterization and Control of Powder Properties for Additive Manufacturing , 2015 .

[5]  Kenneth W. Dalgarno,et al.  An overview of powder granulometry on feedstock and part performance in the selective laser melting process , 2017 .

[6]  Michael Gschweitl,et al.  Qualification of AM parts: Extreme value statistics applied to tomographic measurements , 2017 .

[7]  Tim Freeman,et al.  Effect of particle shape and size on flow properties of lactose powders , 2012 .

[8]  N. Shamsaei,et al.  An overview of Direct Laser Deposition for additive manufacturing; Part II: Mechanical behavior, process parameter optimization and control , 2015 .

[9]  John J. Lewandowski,et al.  Progress Towards Metal Additive Manufacturing Standardization to Support Qualification and Certification , 2017 .

[10]  M. Leu,et al.  Powder characterisation techniques and effects of powder characteristics on part properties in powder-bed fusion processes , 2017 .

[11]  Yukitaka Murakami,et al.  Effects of Nonmetallic Inclusions on Fatigue Strength , 2002 .

[12]  Abdolreza Simchi,et al.  The role of particle size on the laser sintering of iron powder , 2004 .

[13]  Gideon Levy,et al.  Influence of the particle size distribution on surface quality and mechanical properties in AM steel parts , 2011 .

[14]  O. A. Quintana,et al.  Effects of Oxygen Content on Tensile and Fatigue Performance of Ti-6Al-4 V Manufactured by Selective Laser Melting , 2017 .

[15]  T. Niendorf,et al.  Fatigue life of additively manufactured Ti–6Al–4V in the very high cycle fatigue regime , 2017 .

[16]  N. Shamsaei,et al.  Additive manufacturing of fatigue resistant materials: Challenges and opportunities , 2017 .

[17]  Nima Shamsaei,et al.  Surface roughness effects on the fatigue strength of additively manufactured Ti-6Al-4V , 2018, International Journal of Fatigue.

[18]  Thomas Tröster,et al.  Fatigue Strength Prediction for Titanium Alloy TiAl6V4 Manufactured by Selective Laser Melting , 2015, Metallurgical and Materials Transactions A.

[19]  R. German.  Powder metallurgy science , 1984 .

[20]  Ma Qian,et al.  Effect of Powder Reuse Times on Additive Manufacturing of Ti-6Al-4V by Selective Electron Beam Melting , 2015 .

[21]  P. Alvarez,et al.  Effect of IN718 Recycled Powder Reuse on Properties of Parts Manufactured by Means of Selective Laser Melting , 2014 .

[22]  S. Beretta,et al.  A comparison of fatigue strength sensitivity to defects for materials manufactured by AM or traditional processes , 2017 .

[23]  Claus Emmelmann,et al.  Investigation of Aging Processes of Ti-6Al-4 V Powder Material in Laser Melting , 2012 .

[24]  S. Atre,et al.  Effects of powder characteristics and processing conditions on the corrosion performance of 17-4 PH stainless steel fabricated by laser-powder bed fusion , 2018 .

[25]  Ma Qian,et al.  Manipulation and Characterization of a Novel Titanium Powder Precursor for Additive Manufacturing Applications , 2015 .

[26]  David L. Bourell,et al.  Property evaluation of 304L stainless steel fabricated by selective laser melting , 2012 .

[27]  Joakim Karlsson,et al.  Characterization and comparison of materials produced by Electron Beam Melting (EBM) of two different Ti-6Al-4V powder fractions , 2013 .

[28]  J. Beuth,et al.  Thermal conductivity of metal powders for powder bed additive manufacturing , 2018 .

[29]  Mohsen Seifi,et al.  Metal Additive Manufacturing: A Review of Mechanical Properties , 2016 .

[30]  Sean L. Yoder,et al.  Correlations Between Powder Feedstock Quality, In Situ Porosity Detection, and Fatigue Behavior of Ti-6Al-4V Fabricated by Powder Bed Electron Beam Melting: A Step Towards Qualification , 2018, JOM.

[31]  Y. Murakami.  Metal Fatigue: Effects of Small Defects and Nonmetallic Inclusions , 2002 .

[32]  F. Walther,et al.  Fatigue Performance of Laser Additive Manufactured Ti–6Al–4V in Very High Cycle Fatigue Regime up to 109 Cycles , 2015, Front. Mater..

[33]  Jeffrey Malcolm Benson,et al.  The need for powder characterisation in the additive manufacturing industry and the establishment of a national facility , 2015 .

[34]  A. Astarita,et al.  Influence of Powder Characteristics on Formation of Porosity in Additive Manufacturing of Ti-6Al-4V Components , 2017, Journal of Materials Engineering and Performance.