Three-dimensional finite element analysis of single-bolt, single-lap composite bolted joints: Part II––effects of bolt-hole clearance

Abstract Three-dimensional finite element models have been developed to study the effects of bolt-hole clearance on the mechanical behaviour of bolted composite (graphite/epoxy) joints. In Part I of this two-part paper, the model was developed in the finite element code MSC.Marc and validated against experiments and other finite element solutions. In this second part of the paper, results from the model showing the effects of clearance in single-lap, single-bolt joints are presented and compared with experimental results. Both quasi-isotropic and zero-dominated lay-ups are studied. It is shown that increased clearance leads to increased bolt rotation, decreased bolt-hole contact area, and decreased joint stiffness. In single-lap joints, clearance is shown to cause three-dimensional variations in the stress distribution in the laminate, and these variations are also dependent on the lay-up; the radial and tangential stresses in each ply are shown to illustrate this point. Finally, a prediction of the failure onset load using Hashin’s failure criteria is given and the results are compared with experimental results.

[1]  Michael A. McCarthy.  BOJCAS: Bolted joints in composite aircraft structures , 2001 .

[2]  Byung Man Kwak,et al.  Contact analysis of mechanically fastened joints in composite laminates by linear complementarity problem formulation , 1997 .

[3]  M. A. McCarthy,et al.  Bolt-hole clearance effects and strength criteria in single-bolt, single-lap, composite bolted joints , 2002 .

[4]  B. Pradhan,et al.  Stresses Around Partial Contact Pin-Loaded Holes in FRP Composite Plates , 1984 .

[5]  Wen-Hwa Chen,et al.  Three-dimensional contact stress analysis of a composite laminate with bolted joint , 1995 .

[6]  Liyong Tong,et al.  Bearing failure of composite bolted joints with non-uniform bolt-to-washer clearance , 2000 .

[7]  Robert E. Rowlands,et al.  Single- and multiple-bolted joints in orthotropic materials , 1982 .

[8]  T. S. Ramamurthy.  New studies on the effect of bearing loads in lugs with clearance fit pins , 1989 .

[9]  Z. Hashin.  Failure Criteria for Unidirectional Fiber Composites , 1980 .

[10]  Isaac M Daniel,et al.  Composite Materials: Testing and Design , 1982 .

[11]  Theo de Jong,et al.  Stresses Around Pin-Loaded Holes in Elastically Orthotropic or Isotropic Plates , 1977 .

[12]  F. Cappello,et al.  On the Elastic Behavior of a Cross-Ply Composite Pin-Joint with Clearance Fits , 1999 .

[13]  Fabrice Pierron,et al.  A Numerical and Experimental Study of Woven Composite Pin-Joints , 2000 .

[14]  Fan Weixun,et al.  Load distribution of multi-fastener laminated composite joints , 1993 .

[15]  P Shyprykevich,et al.  Characterization of Bolted Joint Behavior: MIL-HDBK-17 Accomplishments at Standardization , 1995 .

[16]  D. E. Cooper,et al.  The Effects of Pin Elasticity, Clearance, and Friction on the Stresses in a Pin-Loaded Orthotropic Plate , 1987 .

[17]  Erdogan Madenci,et al.  Bolted double-lap composite joints under mechanical and thermal loading , 2001 .

[18]  J. Whitney,et al.  Stress Fracture Criteria for Laminated Composites Containing Stress Concentrations , 1974 .

[19]  Tomas Ireman,et al.  Three-dimensional stress analysis of bolted single-lap composite joints , 1998 .

[20]  Surachate Chutima,et al.  Effect of pitch distance, row spacing, end distance and bolt diameter on multi-fastened composite joints , 1996 .

[21]  John H. Crews,et al.  Stress analysis method for a clearance-fit bolt under bearing loads , 1986 .

[22]  S. Kim,et al.  Finite element analysis of laminated composite plates with multi-pin joints considering friction , 1995 .