Die optimization design and experimental study of a large wallboard aluminum alloy profile used for high-speed train

The extrusion die plays a crucial role in the quality control of aluminum alloy profile production. But in practice, the design of extrusion die is mainly dependent on the experience and intuition of die designers; thus, many times of modifications and experiments should be undergone until an acceptable product is gained. In this paper, the extrusion process of a large wallboard aluminum alloy profile used for high-speed train was simulated by means of HyperXtrude software, and the flow behavior of material and deformation mechanism in the die cavity were investigated. With the simulation results of the initial die design scheme, a nonuniform velocity distribution in cross-section of the extrudate was observed. For optimizing the die design scheme, two optimal schemes (adoption of double-step welding chamber and introduction of baffle plate) were proposed. Through optimization, the velocity differences in the extrudate for optimal schemes are decreased from 39.9 to 12.2 and 10.8 mm/s, respectively. Thus, the uniformity of velocity distribution was improved in optimal schemes. The extrusion die design methods for large wallboard profiles were summarized and proposed, including the design methods of baffle plate and double-step welding chamber. Through trial production, a sound wallboard aluminum profile with good geometric shape and high dimensional accuracy was gained. Additionally, the mechanical properties of the extrudate were examined by means of experimental method. It is found that the test results stratified the practical engineering requirements.

[1]  J. Huetink,et al.  3D FEM simulation of stationary metal forming processes with applications to slitting and rolling , 2004 .

[2]  Lorenzo Donati,et al.  The prediction of seam welds quality in aluminum extrusion , 2004 .

[3]  Shijian Yuan,et al.  Effect of inner cone punch on metal flow in extrusion process , 2009 .

[4]  Ma Xinwu,et al.  Numerical Simulation and Die Structure Optimization of an Aluminum Rectangular Hollow Pipe Extrusion Process , 2006 .

[5]  Abul Fazal M. Arif,et al.  VARIATION OF PRESSURE WITH RAM SPEED AND DIE PROFILE IN HOT EXTRUSION OF ALUMINUM-6063 , 2001 .

[6]  Xueyu Ruan,et al.  Finite volume simulation and mould optimization of aluminum profile extrusion , 2007 .

[7]  N. R. Chitkara,et al.  Development of an Adaptive Directional Reduced Integration Technique and its Application to Rigid-Plastic Finite-Element Analysis of Heading and Backward Extrusion , 2002 .

[8]  S. H. Kim,et al.  Investigation of lubrication effect on the backward extrusion of thin-walled rectangular aluminum case with large aspect ratio , 2006 .

[9]  Guillaume Houzeaux,et al.  The fixed-mesh ALE approach for the numerical approximation of flows in moving domains , 2009, J. Comput. Phys..

[10]  Kim Seng Lee,et al.  Feature-Based Parametric Design of a Gating System for a Die-Casting Die , 2002 .

[11]  J Lof,et al.  FEM simulations of the extrusion of complex thin-walled aluminium sections , 2002 .

[12]  Guoqun Zhao,et al.  Optimization of an aluminum profile extrusion process based on Taguchi’s method with S/N analysis , 2012 .

[13]  Seon-Bong Lee,et al.  Prediction of Welding Pressure in the Non Steady state Porthole Die Extrusion of AI7003 Tubes , 2002 .

[14]  Mohamed S. Gadala,et al.  ALE formulation and its application in solid mechanics , 1998 .

[15]  Chun-Yin Wu,et al.  Optimal Shape Design of an Extrusion Die Using Polynomial Networks and Genetic Algorithms , 2002 .

[16]  B. Gautham,et al.  Prediction of extrudate swell in polymer melt extrusion using an Arbitrary Lagrangian Eulerian (ALE) based finite element method , 2009 .

[17]  Jie Zhou,et al.  Effect of pocket design on metal flow through single-bearing extrusion dies to produce a thin-walled aluminium profile , 2008 .

[18]  Chung-Gil Kang,et al.  Effects of chamber shapes of porthole die on elastic deformation and extrusion process in condenser tube extrusion , 2005 .

[19]  G. J. Creus,et al.  Simulation of 3D metal-forming using an arbitrary Lagrangian–Eulerian finite element method , 2001 .

[20]  J. S. Gunasekera,et al.  3D flow analysis inside shear and streamlined extrusion dies for feeder plate design , 2001 .

[21]  G. Y. Li,et al.  Numerical and experimental study on the extrusion through a porthole die to produce a hollow magnesium profile with longitudinal weld seams , 2008 .

[22]  Dong-Yol Yang,et al.  Integrated finite element simulation for the hot extrusion of complicated Al alloy profiles , 2001 .

[23]  Jian Wang,et al.  Tribological behavior of Ti2SnC particulate reinforced copper matrix composites , 2006 .